Ball formation is the first step in wire bonding of semiconductor chips to their lead frames. An electric discharge melts the wire and surface tension causes the melt to roll up into a ball; the ball is subsequently pressed onto the proper bond pad on the chip to make a ball bond. In the ball bonding process, the electrical discharge characteristics, the associated heat transport, and the wire material determine the nature of the ball formed. The discharge shows sensitivity to the polarity of the wire. Experiments with upscaled aluminum and copper wires in air at reduced pressure show that the heat transfer to the wire associated with the discharge is significantly greater when the wire is the anode than when the wire is the cathode. These experiments included temperature measurements in real time made by fine thermocouples implanted in upscaled wires. In aluminum the anode wire receives twice as much energy from the arc as the cathode wire. In copper the anode wire receives three times as much energy from the arc as the cathode. Our conclusions are also reinforced by metallographic examination of sectioned balls.
Skip Nav Destination
Article navigation
March 1991
Research Papers
Effect of Polarity on Heat Transfer in the Ball Formation Process
L. J. Huang,
L. J. Huang
Harrison Radiator Division, GMC, Lockport, NY 14094
Search for other works by this author on:
M. A. Jog,
M. A. Jog
Department of Mechanical Engineering and Applied Mechanics, University of Pennsylvania, Philadelphia, PA 19104-6315
Search for other works by this author on:
I. M. Cohen,
I. M. Cohen
Department of Mechanical Engineering and Applied Mechanics, University of Pennsylvania, Philadelphia, PA 19104-6315
Search for other works by this author on:
P. S. Ayyaswamy
P. S. Ayyaswamy
Department of Mechanical Engineering and Applied Mechanics, University of Pennsylvania, Philadelphia, PA 19104-6315
Search for other works by this author on:
L. J. Huang
Harrison Radiator Division, GMC, Lockport, NY 14094
M. A. Jog
Department of Mechanical Engineering and Applied Mechanics, University of Pennsylvania, Philadelphia, PA 19104-6315
I. M. Cohen
Department of Mechanical Engineering and Applied Mechanics, University of Pennsylvania, Philadelphia, PA 19104-6315
P. S. Ayyaswamy
Department of Mechanical Engineering and Applied Mechanics, University of Pennsylvania, Philadelphia, PA 19104-6315
J. Electron. Packag. Mar 1991, 113(1): 33-39 (7 pages)
Published Online: March 1, 1991
Article history
Received:
June 18, 1990
Revised:
January 4, 1991
Online:
April 28, 2008
Citation
Huang, L. J., Jog, M. A., Cohen, I. M., and Ayyaswamy, P. S. (March 1, 1991). "Effect of Polarity on Heat Transfer in the Ball Formation Process." ASME. J. Electron. Packag. March 1991; 113(1): 33–39. https://doi.org/10.1115/1.2905364
Download citation file:
Get Email Alerts
Cited By
Sequential Versus Concurrent Effects in Combined Stress Solder Joint Reliability
J. Electron. Packag
Related Articles
Heat Transfer in Wire Bonding Process
J. Electron. Packag (March,1994)
Distortion in Thermal Field Around Inserted Thermocouples in Experimental Interfacial Studies, Part 4: End Effect
J. Manuf. Sci. Eng (February,2002)
Mechanical and Electrical Properties of Au-Al and Cu-Al Intermetallics Layer at Wire Bonding Interface
J. Electron. Packag (December,2003)
A Dual-Scale Computational Method for Correcting Surface Temperature
Measurement Errors
J. Heat Transfer (August,2004)
Related Proceedings Papers
Related Chapters
Recovery of Gold Ions from Copper Anode Slime by Means of Magnetite Nanoparticles
International Conference on Computer and Electrical Engineering 4th (ICCEE 2011)
Nonferrous Material
Metric Standards for Worldwide Manufacturing, 2007 Edition