The performance of a novel impinging two-phase jet heat sink operating with single and multiple jets is presented and the influence of the following parameters is quantified: (i) thermal load applied on the heat sink and (ii) geometrical arrangement of the orifices (jets). The heat sink is part of a vapor compression cooling system equipped with an R-134a small-scale oil-free linear motor compressor. The evaporator and the expansion device are integrated into a single cooling unit. The expansion device can be a single orifice or an array of orifices responsible for the generation of two-phase jet(s) impinging on a surface where a concentrated heat load is applied. The analysis is based on the thermodynamic performance and steady-state heat transfer parameters associated with the impinging jet(s) for single and multiple orifice tests. The two-phase jet heat sink was capable of dissipating cooling loads of up to 160 W and 200 W from a 6.36 cm2 surface for single and multiple orifice configurations, respectively. For these cases, the temperature of the impingement surface was kept below 40 °C and the average heat transfer coefficient reached values between 14,000 and 16,000 W/(m2 K).
Issue Section:
Research Papers
Keywords:
Thermal analysis
References
1.
Smakulski
, P.
, and Pietrowicz
, S.
, 2016
, “A Review of the Capabilities of High Heat Flux Removal by Porous Materials, Microchannels and Spray Cooling Techniques
,” Appl. Therm. Eng.
, 104
, pp. 636
–646
.2.
Bar-Cohen
, A.
, and Holloway
, C. A.
, 2014
, “Thermal Science and Engineering—From Macro to Nano in 200 Years
,” 15th International Heat Transfer Conference
(IHTC-15
), Kyoto, Japan, Aug. 10–15, Paper No. IHTC15-FL01.3.
Nakayama
, W.
, Suzuki
, O.
, and Hara
, Y.
, 2009
, “Thermal Management of Electronic and Electrical Devices in Automobile Environment
,” Fifth International IEEE Vehicle Power and Propulsion Conference
(VPPC
), Dearborn, MI, Sept. 7–10, pp. 601
–608
.4.
Mudawar
, I.
, 2001
, “Assessment of High-Heat-Flux Thermal Management Schemes
,” IEEE Trans. Compon. Packag. Technol.
, 24
(2
), pp. 122
–141
.5.
Chu
, R. C.
, Simons
, R. E.
, Ellsworth
, M. J.
, Schmidt
, R. R.
, and Cozzolino
, V.
, 2004
, “Review of Cooling Technologies for Computer Products
,” IEEE Trans. Device Mater. Reliab.
, 4
(4
), pp. 568
–585
.6.
Kheirabadi
, A. C.
, and Groulx
, D.
, 2016
, “Cooling of Server Electronics: A Design Review of Existing Technology
,” Appl. Therm. Eng.
, 105
, pp. 622
–638
.7.
Bar-Cohen
, A.
, Arik
, M.
, and Ohadi
, M.
, 2006
, “Direct Liquid Cooling of High Flux Micro and Nano Electronic Components
,” Proc. IEEE
, 94
(8
), pp. 1549
–1570
.8.
Mudawar
, I.
, Bharathan
, D.
, Kelly
, K.
, and Narumanchi
, S.
, 2008
, “Two-Phase Spray Cooling of Hybrid Vehicle Electronics
,” 11th Intersociety Conference on Thermal and Thermomechanical Phenomena in Electronic Systems
(ITHERM
), Orlando, FL, May 28–31, pp. 1210
–1221
.9.
Agostini
, B.
, Fabbri
, M.
, Park
, J. E.
, Wojtan
, L.
, Thome
, J. R.
, and Michel
, B.
, 2007
, “State of the Art of Heat Flux Cooling Technologies
,” Heat Transfer Eng.
, 28
(4
), pp. 258
–281
.10.
Kandlikar
, S. G.
, and Bapat
, A. V.
, 2007
, “Evaluation of Jet Impingement, Spray and Microchannel Chip Cooling Options for High Heat Flux Removal
,” Heat Transfer Eng.
, 28
(11
), pp. 911
–923
.11.
Ebadian
, M. A.
, and Lin
, C. X.
, 2011
, “A Review of High-Heat-Flux Heat Removal Technologies
,” ASME J. Heat Transfer
, 133
(11
), p. 110801
.12.
Marcinichen
, J. B.
, Olivier
, J. A.
, Lamaison
, N.
, and Thome
, J. R.
, 2013
, “Advances in Electronics Cooling
,” Heat Transfer Eng.
, 34
(5–6
), pp. 434
–446
.13.
Kadam
, S. T.
, and Kumar
, R.
, 2014
, “Twenty First Century Cooling Solution: Microchannel Heat Sinks
,” Int. J. Therm. Sci.
, 85
, pp. 73
–92
.14.
Cheng
, W.-L.
, Zhang
, W.-W.
, Chen
, H.
, and Hu
, L.
, 2016
, “Spray Cooling and Flash Evaporation Cooling: The Current Development and Application
,” Renewable Sustainable Energy Rev.
, 55
, pp. 614
–628
.15.
Riofrío
, M. C.
, Caney
, N.
, and Gruss
, J.-A.
, 2016
, “State of the Art of Efficient Pumped Two-Phase Flow Cooling Technologies
,” Appl. Therm. Eng.
, 104
, pp. 333
–343
.16.
Barbosa
, J. R.
, Jr., Ribeiro
, G. B.
, and Oliveira
, P. A.
, 2012
, “A State-of-the-Art Review of Compact Vapor Compression Refrigeration Systems and Their Applications
,” Heat Transfer Eng.
, 33
(4–5
), pp. 356
–374
.17.
Trutassanawin
, S.
, Groll
, E.
, Garimella
, S. V.
, and Cremaschi
, L.
, 2006
, “Experimental Investigation of a Miniature-Scale Refrigeration System for Electronics Cooling
,” IEEE Trans. Compon. Packag. Technol.
, 29
(3
), pp. 678
–687
.18.
Marcinichen
, J. B.
, Thome
, J. R.
, and Michel
, B.
, 2010
, “Cooling of Microprocessors With Micro-Evaporation: A Novel Two-Phase Cooling Cycle
,” Int. J. Refrig.
, 33
(7
), pp. 1264
–1276
.19.
Marcinichen
, J. B.
, Olivier
, J. A.
, de Oliveira
, V.
, and Thome
, J. R.
, 2012
, “A Review of On-Chip Micro-Evaporation: Experimental Evaluation of Liquid Pumping and Vapor Compression Driven Cooling Systems and Control
,” Appl. Energy
, 92
, pp. 147
–161
.20.
Mancin
, S.
, Zilio
, C.
, Righetti
, G.
, and Rossetto
, L.
, 2013
, “Mini Vapor Cycle System for High Density Electronic Cooling Applications
,” Int. J. Refrig.
, 36
(4
), pp. 1191
–1202
.21.
Womac
, D. J.
, Ramadhyani
, S.
, and Incropera
, F. P.
, 1993
, “Correlating Equations for Impingement Cooling of Small Heat Sources With Single Circular Liquid Jets
,” ASME J. Heat Transfer
, 115
(1
), pp. 106
–115
.22.
Garimella
, S. V.
, and Rice
, R. A.
, 1995
, “Confined and Submerged Liquid Jet Impingement Heat Transfer
,” ASME J. Heat Transfer
, 117
(4
), pp. 871
–877
.23.
Lienhard
, V. J. H.
, 1995
, “Liquid Jet Impingement
,” Annual Review of Heat Transfer
, Vol. 6
, Begell House, New York, pp. 199
–270
.24.
Pan
, Y.
, and Webb
, B. W.
, 1995
, “Heat Transfer Characteristics of Arrays of Free-Surface Liquid Jets
,” ASME J. Heat Transfer
, 117
(4
), pp. 878
–883
.25.
Whelan
, B. P.
, and Robinson
, A. J.
, 2009
, “Nozzle Geometry Effects in Liquid Jet Array Impingement
,” Appl. Therm. Eng.
, 29
(11–12
), pp. 2211
–2221
.26.
Lindeman
, B. A.
, and Shedd
, T. A.
, 2013
, “Comparison of Empirical Correlations and a Two-Equation Predictive Model for Heat Transfer to Arbitrary Arrays of Single-Phase Impinging Jets
,” Int. J. Heat Mass Transfer
, 66
, pp. 772
–780
.27.
San
, J.-Y.
, and Chen
, J.-J.
, 2014
, “Effects of Jet-to-Jet Spacing and Jet Height on Heat Transfer Characteristics of an Impinging Jet Array
,” Int. J. Heat Mass Transfer
, 71
, pp. 8
–17
.28.
Qiu
, L.
, Dubey
, S.
, Choo
, F. H.
, and Duan
, F.
, 2015
, “Recent Developments of Jet Impingement Nucleate Boiling
,” Int. J. Heat Mass Transfer
, 89
, pp. 42
–58
.29.
Fabbri
, M.
, Jiang
, S.
, and Dhir
, V. K.
, 2005
, “A Comparative Study of Cooling of High Power Density Electronics Using Sprays and Microjets
,” ASME J. Heat Transfer
, 127
(1
), pp. 38
–48
.30.
Meyer
, M. T.
, Mudawar
, I.
, Boyack
, C. E.
, and Hale
, C. A.
, 2006
, “Single-Phase and Two-Phase Cooling With an Array of Rectangular Jets
,” Int. J. Heat Mass Transfer
, 49
(1–2
), pp. 17
–29
.31.
Browne
, E. A.
, Michna
, G. J.
, Jensen
, M. K.
, and Peles
, Y.
, 2010
, “Microjet Array Single-Phase and Flow Boiling Heat Transfer With R-134a
,” Int. J. Heat Mass Transfer
, 53
(23–24
), pp. 5027
–5034
.32.
Wang
, Z. Y.
, Wong
, T. N.
, and Duan
, F.
, 2011
, “Submerged Liquid Jet Impingement Cooling
,” 13th Electronics Packaging Technology Conference
(EPTC
), Singapore, Dec. 7–9, pp. 660
–666
.33.
Whelan
, B. P.
, Kempers
, R.
, and Robinson
, A. J.
, 2012
, “A Liquid-Based System for CPU Cooling Implementing a Jet Array Impingement Waterblock and a Tube Array Remote Heat Exchanger
,” Appl. Therm. Eng.
, 39
, pp. 86
–94
.34.
Parida
, P. R.
, Ekkad
, S. V.
, and Ngo
, K.
, 2012
, “Impingement-Based High Performance Cooling Configurations for Automotive Power Converters
,” Int. J. Heat Mass Transfer
, 55
(4
), pp. 834
–847
.35.
Buchanan
, R. A.
, and Shedd
, T. A.
, 2013
, “Extensive Parametric Study of Heat Transfer to Arrays of Oblique Impinging Jets With Phase Change
,” ASME J. Heat Transfer
, 135
(11
), p. 111017
.36.
Joshi
, S. N.
, Rau
, M. J.
, Dede
, E. M.
, and Garimella
, S. V.
, 2013
, “An Experimental Study of a Multi-Device Jet Impingement Cooler With Phase Change Using HFE-7100
,” ASME
Paper No. HT2013-17059.37.
Joshi
, S. N.
, Rau
, M. J.
, and Dede
, E. M.
, 2013
, “An Experimental Study of a Single-Device Jet Impingement Cooler With Phase Change Using HFE-7100 and a Vapor Extraction Manifold
,” ASME
Paper No. IMECE2013-63249.38.
Joshi
, S. N.
, and Dede
, E. M.
, 2015
, “Effect of Sub-Cooling on Performance of a Multi-Jet Two Phase Cooler With Multi-Scale Porous Surfaces
,” Int. J. Therm. Sci.
, 87
, pp. 110
–120
.39.
Maddox
, J. F.
, Knight
, R. W.
, and Bhavnani
, S. H.
, 2015
, “Local Thermal Measurements of a Confined Array of Impinging Liquid Jets for Power Electronics Cooling
,” 31st Semiconductor Thermal Measurement, Modeling and Management Symposium
, (SEMI-THERM
), San Jose, CA, Mar. 15–19, pp. 228
–234
.40.
Gould
, K.
, Cai
, S. Q.
, Neft
, C.
, and Bhunia
, A.
, 2015
, “Liquid Jet Impingement Cooling of a Silicon Carbide Power Conversion Module for Vehicle Applications
,” IEEE Trans. Power Electron.
, 30
(6
), pp. 2975
–2984
.41.
Sung
, M. K.
, and Mudawar
, I.
, 2009
, “CHF Determination for High-Heat Flux Phase Change Cooling System Incorporating Both Micro-Channel Flow and Jet Impingement
,” Int. J. Heat Mass Transfer
, 52
(3–4
), pp. 610
–619
.42.
Sung
, M. K.
, and Mudawar
, I.
, 2008
, “Single-Phase and Two-Phase Cooling Using Hybrid Micro-Channel/Slot-Jet Module
,” Int. J. Heat Mass Transfer
, 51
(15–16
), pp. 3825
–3839
.43.
Sung
, M. K.
, and Mudawar
, I.
, 2008
, “Single-Phase and Two-Phase Heat Transfer Characteristics of Low Temperature Hybrid Micro-Channel/Micro-Jet Impingement Cooling Module
,” Int. J. Heat Mass Transfer
, 51
(15–16
), pp. 3882
–3895
.44.
Barrau
, J.
, Chemisana
, D.
, Rosell
, J.
, Tadrist
, L.
, and Ibañez
, M.
, 2010
, “An Experimental Study of a New Hybrid Jet Impingement/Micro-Channel Cooling Scheme
,” Appl. Therm. Eng.
, 30
(14–15
), pp. 2058
–2066
.45.
Chien
, L.-H.
, Liao
, W.-R.
, and Liu
, H.-Y.
, 2014
, “An Experimental Study of Two-Phase Convection in Micro-Channels With Impinging FC-72 Jets
,” Appl. Therm. Eng.
, 67
(1–2
), pp. 159
–167
.46.
Muszynski
, T.
, and Andrzejczyk
, R.
, 2016
, “Heat Transfer Characteristics of Hybrid Microjet-Microchannel Cooling Module
,” Appl. Therm. Eng.
, 93
, pp. 1360
–1366
.47.
Yan
, Z. B.
, Toh
, K. C.
, Duan
, F.
, Wong
, T. N.
, Choo
, K. F.
, Chan
, P. K.
, and Chua
, Y. S.
, 2010
, “Experimental Study of Impingement Spray Cooling for High Power Devices
,” Appl. Therm. Eng.
, 30
(10
), pp. 1225
–1230
.48.
Chunqiang
, S.
, Shuangquan
, S.
, Changqing
, T.
, and Hongbo
, X.
, 2012
, “Development and Experimental Investigation of a Novel Spray Cooling System Integrated in Refrigeration Circuit
,” Appl. Therm. Eng.
, 33–34
, pp. 246
–252
.49.
Tan
, Y. B.
, Xie
, J. L.
, Duan
, F.
, Wong
, T. N.
, Toh
, K. C.
, Choo
, K. F.
, Chan
, P. K.
, and Chua
, Y. S.
, 2013
, “Multi-Nozzle Spray Cooling for High Heat Flux Applications in a Closed Loop System
,” Appl. Therm. Eng.
, 54
(2
), pp. 372
–379
.50.
Xie
, J. L.
, Tan
, Y. B.
, Wong
, T. N.
, Duan
, F.
, Toh
, K. C.
, Choo
, K. F.
, Chan
, P. K.
, and Chua
, Y. S.
, 2014
, “Multi-Nozzle Array Spray Cooling for Large Area High Power Devices in a Closed Loop System
,” Int. J. Heat Mass Transfer
, 78
, pp. 1177
–1186
.51.
Xu
, H.
, Si
, C.
, Shao
, S.
, and Tian
, C.
, 2014
, “Experimental Investigation on Heat Transfer of Spray Cooling With Isobutane (R-600a)
,” Int. J. Therm. Sci.
, 86
, pp. 21
–27
.52.
Hou
, Y.
, Liu
, J.
, Su
, X.
, Qian
, Y.
, Liu
, L.
, and Liu
, X.
, 2015
, “Experimental Study on the Characteristics of a Closed Loop R-134a Spray Cooling
,” Exp. Therm. Fluid Sci.
, 61
, pp. 194
–200
.53.
Chen
, S.
, Liu
, J.
, Liu
, X.
, and Hou
, Y.
, 2015
, “An Experimental Comparison of Heat Transfer Characteristic Between R-134a and R-22 in Spray Cooling
,” Exp. Therm. Fluid Sci.
, 66
, pp. 206
–212
.54.
Oliveira
, P. A.
, 2016
, “Development of a Two-Phase Jet Heat Sink Integrated With a Compact Refrigeration System for Electronics Cooling
,” Ph.D. thesis
, Federal University of Santa Catarina, Florianópolis, Brazil.http://www.polo.ufsc.br/fmanager/polo2016/publicacoes/arquivo293_1.pdf55.
Oliveira
, P. A.
, and Barbosa
, J. R.
, Jr., 2017
, “Novel Two-Phase Jet Impingement Heat Sink for Active Cooling of Electronic Devices
,” Appl. Therm. Eng.
, 112
, pp. 952
–964
.56.
Oliveira
, P. A.
, and Barbosa
, J. R.
, Jr., 2016
, “Two-Phase Jet Impingement Heat Sink Integrated With a Compact Vapor Compression System for Electronics Cooling
,” IEEE Intersociety Conference on Thermal and Thermomechanical Phenomena in Electronic Systems
(ITHERM
), Las Vegas, NV, May 31–June 3, pp. 976–986.57.
Lemmon
, E. W.
, Huber
, M. L.
, and McLinden
, M.
, 2007
, “NIST Reference Fluid Thermodynamic and Transport Properties (REFPROP): Version 8.0
,” National Institute of Standards and Technology (NIST), Boulder, CO.58.
Coleman
, H. W.
, and Steele
, W. G.
, 2009
, Experimentation, Validation, and Uncertainty Analysis for Engineers
, 3rd ed., Wiley
, Hoboken, NJ
.59.
Hsieh
, S.-S.
, Fan
, T.-C.
, and Tsai
, H.-H.
, 2004
, “Spray Cooling Characteristics of Water and R-134a—Part I: Nucleate Boiling
,” Int. J. Heat Mass Transfer
, 47
(26
), pp. 5703
–5712
.Copyright © 2017 by ASME
You do not currently have access to this content.
