Skip Nav Destination
Issues
August 1943
This article was originally published in
Transactions of the American Society of Mechanical Engineers
ISSN 0097-6822
In this Issue
Research Papers
Studies of Heat Transmission Through Boiler Tubing at Pressures From 500 to 3300 Pounds
Trans. ASME. August 1943, 65(6): 553–579.
doi: https://doi.org/10.1115/1.4018835
Topics:
Boiler tubes
,
Heat transfer
,
Pressure drop
,
Temperature
,
Metals
,
Steam
,
Water
,
Heat
,
Absorption
,
Boilers
Influence of Nonuniform Development of Heat Upon the Temperature Distribution in Electrical Coils and Similar Heat Sources of Simple Form
Trans. ASME. August 1943, 65(6): 593–602.
doi: https://doi.org/10.1115/1.4018847
Topics:
Heat
,
Temperature distribution
,
Temperature
,
Shapes
,
Electrical resistance
,
Chemical reactions
,
Cylinders
,
Steady state
,
Stress
The Numerical Solution of Heat-Conduction Problems
Trans. ASME. August 1943, 65(6): 607–612.
doi: https://doi.org/10.1115/1.4018854
Effectiveness of Shear-Stressed Rubber Compounds in Isolating Machinery Vibration
Trans. ASME. August 1943, 65(6): 617–622.
doi: https://doi.org/10.1115/1.4018861
Topics:
Machinery
,
Rubber compounds
,
Shear (Mechanics)
,
Vibration
,
Testing
Aerodynamic Center, Control and Stability of Airplanes
Trans. ASME. August 1943, 65(6): 625–628.
doi: https://doi.org/10.1115/1.4018865
Topics:
Aircraft
,
Stability
,
Flight
,
Center of mass
,
Propellers
,
Airfoils
,
Elevators
,
Lift (Fluid dynamics)
,
Static stability
,
Wings
Centrifugal-Pump Performance as a Function of Specific Speed
Trans. ASME. August 1943, 65(6): 629–636.
doi: https://doi.org/10.1115/1.4018866
Topics:
Centrifugal pumps
,
Leakage
,
Disks
,
Flow (Dynamics)
,
Friction
,
Impellers
,
Pumps
,
Reynolds number
New Five-Bar and Six-Bar Linkages in Three Dimensions
Trans. ASME. August 1943, 65(6): 649–656.
doi: https://doi.org/10.1115/1.4018877
Topics:
Dimensions
,
Linkages
,
Economics
,
Oscillations
,
Rotation
A Brief Account of Modern Kinematics
Trans. ASME. August 1943, 65(6): 663–675.
doi: https://doi.org/10.1115/1.4018881
Topics:
Kinematics
,
Engineers
Rating Supercharged Engines on the Basis of the Mean Temperature of the Cycle
Trans. ASME. August 1943, 65(6): 685–690.
doi: https://doi.org/10.1115/1.4018885
Topics:
Cycles
,
Supercharged engines
,
Temperature
,
Clearances (Engineering)
,
Diesel engines
,
Engines
,
Gases
,
Horsepower
,
Brakes
,
Cooling
Inlet-Air-Temperature Correction in a Roots Supercharger
Trans. ASME. August 1943, 65(6): 697–699.
doi: https://doi.org/10.1115/1.4018892
Topics:
Superchargers
,
Temperature
,
Pressure
A Practical Way to Prevent Embrittlement Cracking
Trans. ASME. August 1943, 65(6): 701–704.
doi: https://doi.org/10.1115/1.4018895
Topics:
Cracking (Materials)
,
Embrittlement
,
Fracture (Process)
,
Boilers
,
Hazardous substances
,
Sensors
,
Sodium
,
Water
,
Water treatment
Discussions and Closures
Discussion: “Studies of Heat Transmission Through Boiler Tubing at Pressures From 500 to 3300 Pounds” (Davidson, W. F., Hardie, P. H., Humphreys, C. G. R., Markson, A. A., Mumford, A. R., and Ravese, T., 1943, Trans. ASME, 65, pp. 553–579)
Trans. ASME. August 1943, 65(6): 579.
doi: https://doi.org/10.1115/1.4018836
Topics:
Boiler tubes
,
Heat transfer
Discussion: “Studies of Heat Transmission Through Boiler Tubing at Pressures From 500 to 3300 Pounds” (Davidson, W. F., Hardie, P. H., Humphreys, C. G. R., Markson, A. A., Mumford, A. R., and Ravese, T., 1943, Trans. ASME, 65, pp. 553–579)
Trans. ASME. August 1943, 65(6): 579–580.
doi: https://doi.org/10.1115/1.4018837
Topics:
Boiler tubes
,
Heat transfer
Discussion: “Studies of Heat Transmission Through Boiler Tubing at Pressures From 500 to 3300 Pounds” (Davidson, W. F., Hardie, P. H., Humphreys, C. G. R., Markson, A. A., Mumford, A. R., and Ravese, T., 1943, Trans. ASME, 65, pp. 553–579)
Trans. ASME. August 1943, 65(6): 580–581.
doi: https://doi.org/10.1115/1.4018838
Topics:
Boiler tubes
,
Heat transfer
Discussion: “Studies of Heat Transmission Through Boiler Tubing at Pressures From 500 to 3300 Pounds” (Davidson, W. F., Hardie, P. H., Humphreys, C. G. R., Markson, A. A., Mumford, A. R., and Ravese, T., 1943, Trans. ASME, 65, pp. 553–579)
Trans. ASME. August 1943, 65(6): 581–585.
doi: https://doi.org/10.1115/1.4018839
Topics:
Boiler tubes
,
Heat transfer
Discussion: “Studies of Heat Transmission Through Boiler Tubing at Pressures From 500 to 3300 Pounds” (Davidson, W. F., Hardie, P. H., Humphreys, C. G. R., Markson, A. A., Mumford, A. R., and Ravese, T., 1943, Trans. ASME, 65, pp. 553–579)
Trans. ASME. August 1943, 65(6): 585.
doi: https://doi.org/10.1115/1.4018840
Topics:
Boiler tubes
,
Heat transfer
Discussion: “Studies of Heat Transmission Through Boiler Tubing at Pressures From 500 to 3300 Pounds” (Davidson, W. F., Hardie, P. H., Humphreys, C. G. R., Markson, A. A., Mumford, A. R., and Ravese, T., 1943, Trans. ASME, 65, pp. 553–579)
Trans. ASME. August 1943, 65(6): 585–587.
doi: https://doi.org/10.1115/1.4018841
Topics:
Boiler tubes
,
Heat transfer
Discussion: “Studies of Heat Transmission Through Boiler Tubing at Pressures From 500 to 3300 Pounds” (Davidson, W. F., Hardie, P. H., Humphreys, C. G. R., Markson, A. A., Mumford, A. R., and Ravese, T., 1943, Trans. ASME, 65, pp. 553–579)
Trans. ASME. August 1943, 65(6): 587.
doi: https://doi.org/10.1115/1.4018842
Topics:
Boiler tubes
,
Heat transfer
Discussion: “Studies of Heat Transmission Through Boiler Tubing at Pressures From 500 to 3300 Pounds” (Davidson, W. F., Hardie, P. H., Humphreys, C. G. R., Markson, A. A., Mumford, A. R., and Ravese, T., 1943, Trans. ASME, 65, pp. 553–579)
Trans. ASME. August 1943, 65(6): 587–588.
doi: https://doi.org/10.1115/1.4018843
Topics:
Boiler tubes
,
Heat transfer
Discussion: “Studies of Heat Transmission Through Boiler Tubing at Pressures From 500 to 3300 Pounds” (Davidson, W. F., Hardie, P. H., Humphreys, C. G. R., Markson, A. A., Mumford, A. R., and Ravese, T., 1943, Trans. ASME, 65, pp. 553–579)
Trans. ASME. August 1943, 65(6): 588–589.
doi: https://doi.org/10.1115/1.4018844
Topics:
Boiler tubes
,
Heat transfer
Discussion: “Studies of Heat Transmission Through Boiler Tubing at Pressures From 500 to 3300 Pounds” (Davidson, W. F., Hardie, P. H., Humphreys, C. G. R., Markson, A. A., Mumford, A. R., and Ravese, T., 1943, Trans. ASME, 65, pp. 553–579)
Trans. ASME. August 1943, 65(6): 589–590.
doi: https://doi.org/10.1115/1.4018845
Topics:
Boiler tubes
,
Heat transfer
Closure to “Discussions of ‘Studies of Heat Transmission Through Boiler Tubing at Pressures From 500 to 3300 Pounds’” (1943, Trans. ASME, 65, pp. 579–590)
Trans. ASME. August 1943, 65(6): 590–591.
doi: https://doi.org/10.1115/1.4018846
Topics:
Boiler tubes
,
Heat transfer
Discussion: “Influence of Nonuniform Development of Heat Upon the Temperature Distribution in Electrical Coils and Similar Heat Sources of Simple Form” (Jakob, Max, 1943, Trans. ASME, 65, pp. 593–602)
Trans. ASME. August 1943, 65(6): 602.
doi: https://doi.org/10.1115/1.4018848
Topics:
Heat
,
Temperature distribution
Discussion: “Influence of Nonuniform Development of Heat Upon the Temperature Distribution in Electrical Coils and Similar Heat Sources of Simple Form” (Jakob, Max, 1943, Trans. ASME, 65, pp. 593–602)
Trans. ASME. August 1943, 65(6): 602–603.
doi: https://doi.org/10.1115/1.4018849
Topics:
Heat
,
Temperature distribution
Discussion: “Influence of Nonuniform Development of Heat Upon the Temperature Distribution in Electrical Coils and Similar Heat Sources of Simple Form” (Jakob, Max, 1943, Trans. ASME, 65, pp. 593–602)
Trans. ASME. August 1943, 65(6): 603–604.
doi: https://doi.org/10.1115/1.4018850
Topics:
Heat
,
Temperature distribution
Discussion: “Influence of Nonuniform Development of Heat Upon the Temperature Distribution in Electrical Coils and Similar Heat Sources of Simple Form” (Jakob, Max, 1943, Trans. ASME, 65, pp. 593–602)
Trans. ASME. August 1943, 65(6): 604.
doi: https://doi.org/10.1115/1.4018851
Topics:
Heat
,
Temperature distribution
Discussion: “Influence of Nonuniform Development of Heat Upon the Temperature Distribution in Electrical Coils and Similar Heat Sources of Simple Form” (Jakob, Max, 1943, Trans. ASME, 65, pp. 593–602)
Trans. ASME. August 1943, 65(6): 604.
doi: https://doi.org/10.1115/1.4018852
Topics:
Heat
,
Temperature distribution
Closure to “Discussions of ‘Influence of Nonuniform Development of Heat Upon the Temperature Distribution in Electrical Coils and Similar Heat Sources of Simple Form’” (1943, Trans. ASME, 65, pp. 602–604)
Trans. ASME. August 1943, 65(6): 604–605.
doi: https://doi.org/10.1115/1.4018853
Topics:
Heat
,
Temperature distribution
Discussion: “The Numerical Solution of Heat-Conduction Problems” (Emmons, H. W., 1943, Trans. ASME, 65, pp. 607–612)
Trans. ASME. August 1943, 65(6): 612–613.
doi: https://doi.org/10.1115/1.4018855
Topics:
Heat conduction
Discussion: “The Numerical Solution of Heat-Conduction Problems” (Emmons, H. W., 1943, Trans. ASME, 65, pp. 607–612)
Trans. ASME. August 1943, 65(6): 613.
doi: https://doi.org/10.1115/1.4018856
Topics:
Heat conduction
Discussion: “The Numerical Solution of Heat-Conduction Problems” (Emmons, H. W., 1943, Trans. ASME, 65, pp. 607–612)
Trans. ASME. August 1943, 65(6): 613.
doi: https://doi.org/10.1115/1.4018857
Topics:
Heat conduction
Discussion: “The Numerical Solution of Heat-Conduction Problems” (Emmons, H. W., 1943, Trans. ASME, 65, pp. 607–612)
Trans. ASME. August 1943, 65(6): 613.
doi: https://doi.org/10.1115/1.4018858
Topics:
Heat conduction
Discussion: “The Numerical Solution of Heat-Conduction Problems” (Emmons, H. W., 1943, Trans. ASME, 65, pp. 607–612)
Trans. ASME. August 1943, 65(6): 613–614.
doi: https://doi.org/10.1115/1.4018859
Topics:
Heat conduction
Closure to “Discussions of ‘The Numerical Solution of Heat-Conduction Problems’” (1943, Trans. ASME, 65, pp. 612–614)
Trans. ASME. August 1943, 65(6): 614–615.
doi: https://doi.org/10.1115/1.4018860
Topics:
Heat conduction
Discussion: “Effectiveness of Shear-Stressed Rubber Compounds in Isolating Machinery Vibration” (Madden, Jr., Baxter C., 1943, Trans. ASME, 65, pp. 617–622)
Trans. ASME. August 1943, 65(6): 622.
doi: https://doi.org/10.1115/1.4018862
Topics:
Machinery
,
Rubber compounds
,
Shear (Mechanics)
,
Vibration
Discussion: “Effectiveness of Shear-Stressed Rubber Compounds in Isolating Machinery Vibration” (Madden, Jr., Baxter C., 1943, Trans. ASME, 65, pp. 617–622)
Trans. ASME. August 1943, 65(6): 622–623.
doi: https://doi.org/10.1115/1.4018863
Topics:
Machinery
,
Rubber compounds
,
Shear (Mechanics)
,
Vibration
Closure to “Discussions of ‘Effectiveness of Shear-Stressed Rubber Compounds in Isolating Machinery Vibration’” (1943, Trans. ASME, 65, pp. 622–623)
Trans. ASME. August 1943, 65(6): 623–624.
doi: https://doi.org/10.1115/1.4018864
Topics:
Machinery
,
Rubber compounds
,
Shear (Mechanics)
Discussion: “Centrifugal-Pump Performance as a Function of Specific Speed” (Stepanoff, A. J., 1943, Trans. ASME, 65, pp. 629–636)
Trans. ASME. August 1943, 65(6): 636–637.
doi: https://doi.org/10.1115/1.4018867
Topics:
Centrifugal pumps
Discussion: “Centrifugal-Pump Performance as a Function of Specific Speed” (Stepanoff, A. J., 1943, Trans. ASME, 65, pp. 629–636)
Trans. ASME. August 1943, 65(6): 637.
doi: https://doi.org/10.1115/1.4018868
Topics:
Centrifugal pumps
Discussion: “Centrifugal-Pump Performance as a Function of Specific Speed” (Stepanoff, A. J., 1943, Trans. ASME, 65, pp. 629–636)
Trans. ASME. August 1943, 65(6): 637–638.
doi: https://doi.org/10.1115/1.4018869
Topics:
Centrifugal pumps
Discussion: “Centrifugal-Pump Performance as a Function of Specific Speed” (Stepanoff, A. J., 1943, Trans. ASME, 65, pp. 629–636)
Trans. ASME. August 1943, 65(6): 638–639.
doi: https://doi.org/10.1115/1.4018870
Topics:
Centrifugal pumps
Discussion: “Centrifugal-Pump Performance as a Function of Specific Speed” (Stepanoff, A. J., 1943, Trans. ASME, 65, pp. 629–636)
Trans. ASME. August 1943, 65(6): 639–640.
doi: https://doi.org/10.1115/1.4018871
Topics:
Centrifugal pumps
Discussion: “Centrifugal-Pump Performance as a Function of Specific Speed” (Stepanoff, A. J., 1943, Trans. ASME, 65, pp. 629–636)
Trans. ASME. August 1943, 65(6): 640–642.
doi: https://doi.org/10.1115/1.4018872
Topics:
Centrifugal pumps
Discussion: “Centrifugal-Pump Performance as a Function of Specific Speed” (Stepanoff, A. J., 1943, Trans. ASME, 65, pp. 629–636)
Trans. ASME. August 1943, 65(6): 642–643.
doi: https://doi.org/10.1115/1.4018873
Topics:
Centrifugal pumps
Discussion: “Centrifugal-Pump Performance as a Function of Specific Speed” (Stepanoff, A. J., 1943, Trans. ASME, 65, pp. 629–636)
Trans. ASME. August 1943, 65(6): 644.
doi: https://doi.org/10.1115/1.4018874
Topics:
Centrifugal pumps
Discussion: “Centrifugal-Pump Performance as a Function of Specific Speed” (Stepanoff, A. J., 1943, Trans. ASME, 65, pp. 629–636)
Trans. ASME. August 1943, 65(6): 644–645.
doi: https://doi.org/10.1115/1.4018875
Topics:
Centrifugal pumps
Closure to “Discussions of ‘Centrifugal-Pump Performance as a Function of Specific Speed’” (1943, Trans. ASME, 65, pp. 636–645)
Trans. ASME. August 1943, 65(6): 645–647.
doi: https://doi.org/10.1115/1.4018876
Topics:
Centrifugal pumps
Discussion: “New Five-Bar and Six-Bar Linkages in Three Dimensions” (Goldberg, Michael, 1943, Trans. ASME, 65, pp. 649–656)
Trans. ASME. August 1943, 65(6): 656.
doi: https://doi.org/10.1115/1.4018878
Topics:
Dimensions
,
Linkages
Discussion: “New Five-Bar and Six-Bar Linkages in Three Dimensions” (Goldberg, Michael, 1943, Trans. ASME, 65, pp. 649–656)
Trans. ASME. August 1943, 65(6): 656–660.
doi: https://doi.org/10.1115/1.4018879
Topics:
Dimensions
,
Linkages
Closure to “Discussions of ‘New Five-Bar and Six-Bar Linkages in Three Dimensions’” (1943, Trans. ASME, 65, pp. 656–660)
Trans. ASME. August 1943, 65(6): 660–661.
doi: https://doi.org/10.1115/1.4018880
Topics:
Linkages
Discussion: “A Brief Account of Modern Kinematics” (de Jonge, A. E. Richard, 1943, Trans. ASME, 65, pp. 663–675)
Trans. ASME. August 1943, 65(6): 675–678.
doi: https://doi.org/10.1115/1.4018882
Topics:
Kinematics
Discussion: “A Brief Account of Modern Kinematics” (de Jonge, A. E. Richard, 1943, Trans. ASME, 65, pp. 663–675)
Trans. ASME. August 1943, 65(6): 678–679.
doi: https://doi.org/10.1115/1.4018883
Topics:
Kinematics
Closure to “Discussions of ‘A Brief Account of Modern Kinematics’” (1943, Trans. ASME, 65, pp. 675–679)
Trans. ASME. August 1943, 65(6): 679–683.
doi: https://doi.org/10.1115/1.4018884
Discussion: “Rating Supercharged Engines on the Basis of the Mean Temperature of the Cycle” (Miller, Ralph, 1943, Trans. ASME, 65, pp. 685–690)
Trans. ASME. August 1943, 65(6): 690.
doi: https://doi.org/10.1115/1.4018886
Topics:
Cycles
,
Supercharged engines
,
Temperature
Discussion: “Rating Supercharged Engines on the Basis of the Mean Temperature of the Cycle” (Miller, Ralph, 1943, Trans. ASME, 65, pp. 685–690)
Trans. ASME. August 1943, 65(6): 690–691.
doi: https://doi.org/10.1115/1.4018887
Topics:
Cycles
,
Supercharged engines
,
Temperature
Discussion: “Rating Supercharged Engines on the Basis of the Mean Temperature of the Cycle” (Miller, Ralph, 1943, Trans. ASME, 65, pp. 685–690)
Trans. ASME. August 1943, 65(6): 691–692.
doi: https://doi.org/10.1115/1.4018888
Topics:
Cycles
,
Supercharged engines
,
Temperature
Discussion: “Rating Supercharged Engines on the Basis of the Mean Temperature of the Cycle” (Miller, Ralph, 1943, Trans. ASME, 65, pp. 685–690)
Trans. ASME. August 1943, 65(6): 692–693.
doi: https://doi.org/10.1115/1.4018889
Topics:
Cycles
,
Supercharged engines
,
Temperature
Discussion: “Rating Supercharged Engines on the Basis of the Mean Temperature of the Cycle” (Miller, Ralph, 1943, Trans. ASME, 65, pp. 685–690)
Trans. ASME. August 1943, 65(6): 693.
doi: https://doi.org/10.1115/1.4018890
Topics:
Cycles
,
Supercharged engines
,
Temperature
Closure to “Discussions of ‘Rating Supercharged Engines on the Basis of the Mean Temperature of the Cycle’” (1943, Trans. ASME, 65, pp. 690–693)
Trans. ASME. August 1943, 65(6): 693–696.
doi: https://doi.org/10.1115/1.4018891
Topics:
Supercharged engines
,
Temperature
Discussion: “Inlet-Air-Temperature Correction in a Roots Supercharger” (Hiersch, F. A., 1943, Trans. ASME, 65, pp. 697–699)
Trans. ASME. August 1943, 65(6): 699–700.
doi: https://doi.org/10.1115/1.4018893
Topics:
Superchargers
,
Temperature
Closure to “Discussion of ‘Inlet-Air-Temperature Correction in a Roots Supercharger’” (1943, Trans. ASME, 65, pp. 699–700)
Trans. ASME. August 1943, 65(6): 700.
doi: https://doi.org/10.1115/1.4018894
Topics:
Temperature
Discussion: “A Practical Way to Prevent Embrittlement Cracking” (Berk, A. A., and Schroeder, W. C., 1943, Trans. ASME, 65, pp. 701–704)
Trans. ASME. August 1943, 65(6): 704.
doi: https://doi.org/10.1115/1.4018896
Topics:
Cracking (Materials)
,
Embrittlement
,
Fracture (Process)
Discussion: “A Practical Way to Prevent Embrittlement Cracking” (Berk, A. A., and Schroeder, W. C., 1943, Trans. ASME, 65, pp. 701–704)
Trans. ASME. August 1943, 65(6): 704–705.
doi: https://doi.org/10.1115/1.4018897
Topics:
Cracking (Materials)
,
Embrittlement
,
Fracture (Process)
Discussion: “A Practical Way to Prevent Embrittlement Cracking” (Berk, A. A., and Schroeder, W. C., 1943, Trans. ASME, 65, pp. 701–704)
Trans. ASME. August 1943, 65(6): 705.
doi: https://doi.org/10.1115/1.4018898
Topics:
Cracking (Materials)
,
Embrittlement
,
Fracture (Process)
Discussion: “A Practical Way to Prevent Embrittlement Cracking” (Berk, A. A., and Schroeder, W. C., 1943, Trans. ASME, 65, pp. 701–704)
Trans. ASME. August 1943, 65(6): 705–706.
doi: https://doi.org/10.1115/1.4018899
Topics:
Cracking (Materials)
,
Embrittlement
,
Fracture (Process)
Discussion: “A Practical Way to Prevent Embrittlement Cracking” (Berk, A. A., and Schroeder, W. C., 1943, Trans. ASME, 65, pp. 701–704)
Trans. ASME. August 1943, 65(6): 706–707.
doi: https://doi.org/10.1115/1.4018900
Topics:
Cracking (Materials)
,
Embrittlement
,
Fracture (Process)
Discussion: “A Practical Way to Prevent Embrittlement Cracking” (Berk, A. A., and Schroeder, W. C., 1943, Trans. ASME, 65, pp. 701–704)
Trans. ASME. August 1943, 65(6): 707–708.
doi: https://doi.org/10.1115/1.4018901
Topics:
Cracking (Materials)
,
Embrittlement
,
Fracture (Process)
Discussion: “A Practical Way to Prevent Embrittlement Cracking” (Berk, A. A., and Schroeder, W. C., 1943, Trans. ASME, 65, pp. 701–704)
Trans. ASME. August 1943, 65(6): 708–709.
doi: https://doi.org/10.1115/1.4018902
Topics:
Cracking (Materials)
,
Embrittlement
,
Fracture (Process)
Discussion: “A Practical Way to Prevent Embrittlement Cracking” (Berk, A. A., and Schroeder, W. C., 1943, Trans. ASME, 65, pp. 701–704)
Trans. ASME. August 1943, 65(6): 709.
doi: https://doi.org/10.1115/1.4018903
Topics:
Cracking (Materials)
,
Embrittlement
,
Fracture (Process)
Closure to “Discussions of ‘A Practical Way to Prevent Embrittlement Cracking’” (1943, Trans. ASME, 65, pp. 704–709)
Trans. ASME. August 1943, 65(6): 709–711.
doi: https://doi.org/10.1115/1.4018904
Topics:
Embrittlement
Email alerts
RSS Feeds
Switching Events of Wakes Shed From Two Short Flapping Side-by-Side Cylinders
J. Fluids Eng (May 2025)