A one-dimensional ring-pack lubrication model developed at MIT is applied to simulate the oil film behavior during the warm-up period of a Kohler spark ignition engine. This is done by making assumptions for the evolution of the oil temperatures during warm-up and that the oil control ring during downstrokes is fully flooded. The ring-pack lubrication model includes features such as three different lubrication regimes, i.e., pure hydrodynamic lubrication, boundary lubrication and pure asperity contact, nonsteady wetting of both inlet and outlet of the piston ring, capability to use all ring face profiles that can be approximated by piece-wise polynomials, and, finally, the ability to model the rheology of multigrade oils. Not surprisingly, the simulations show that by far the most important parameter is the temperature dependence of the oil viscosity.
Skip Nav Destination
Article navigation
January 2001
Technical Papers
Analysis of the Piston Ring/Liner Oil Film Development During Warm-Up for an SI-Engine
K. Froelund,
K. Froelund
Department of Energy Engineering, The Technical University of Denmark, Lyngby, Denmark
Search for other works by this author on:
J. Schramm,
J. Schramm
Department of Energy Engineering, The Technical University of Denmark, Lyngby, Denmark
Search for other works by this author on:
T. Tian,
T. Tian
Sloan Automotive Laboratory, Massachusetts Institute of Technology, Cambridge, MA
Search for other works by this author on:
V. Wong,
V. Wong
Sloan Automotive Laboratory, Massachusetts Institute of Technology, Cambridge, MA
Search for other works by this author on:
S. Hochgreb
S. Hochgreb
Sloan Automotive Laboratory, Massachusetts Institute of Technology, Cambridge, MA
Search for other works by this author on:
K. Froelund
Department of Energy Engineering, The Technical University of Denmark, Lyngby, Denmark
J. Schramm
Department of Energy Engineering, The Technical University of Denmark, Lyngby, Denmark
T. Tian
Sloan Automotive Laboratory, Massachusetts Institute of Technology, Cambridge, MA
V. Wong
Sloan Automotive Laboratory, Massachusetts Institute of Technology, Cambridge, MA
S. Hochgreb
Sloan Automotive Laboratory, Massachusetts Institute of Technology, Cambridge, MA
Contributed by the Internal Combustion Engine Division of THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS for publication in the ASME JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER. Manuscript received by the ICE Division, 23 April 1997; final revision received by the ASME Headquarters, 20 October 2000. Associate Editor: D. Assanis.
J. Eng. Gas Turbines Power. Jan 2001, 123(1): 109-116 (8 pages)
Published Online: October 20, 2000
Article history
Received:
April 23, 1997
Revised:
October 20, 2000
Citation
Froelund , K., Schramm, J., Tian , T., Wong , V., and Hochgreb, S. (October 20, 2000). "Analysis of the Piston Ring/Liner Oil Film Development During Warm-Up for an SI-Engine ." ASME. J. Eng. Gas Turbines Power. January 2001; 123(1): 109–116. https://doi.org/10.1115/1.1341206
Download citation file:
Get Email Alerts
Image-based flashback detection in a hydrogen-fired gas turbine using a convolutional autoencoder
J. Eng. Gas Turbines Power
Fuel Thermal Management and Injector Part Design for LPBF Manufacturing
J. Eng. Gas Turbines Power
An investigation of a multi-injector, premix/micromix burner burning pure methane to pure hydrogen
J. Eng. Gas Turbines Power
Related Articles
Elastohydrodynamic Lubrication: A Gateway to Interfacial Mechanics—Review and Prospect
J. Tribol (October,2011)
The Shear-Thinning Elastohydrodynamic Film Thickness of a Two-Component Mixture
J. Tribol (April,2008)
Modified Reynolds Equation for Non-Newtonian Fluid With Rheological Model in Frequency Domain
J. Tribol (October,2005)
Rheological Behavior of Confined Fluids in Thin Lubricated Contacts
J. Appl. Mech (March,2001)
Related Proceedings Papers
Related Chapters
Effectiveness of Minimum Quantity Lubrication (MQL) for Different Work Materials When Turning by Uncoated Carbide (SNMM and SNMG) Inserts
Proceedings of the 2010 International Conference on Mechanical, Industrial, and Manufacturing Technologies (MIMT 2010)
Tribology of Hydraulic Systems: Hydrodynamic Effects of Surface Roughness
Hydraulic Failure Analysis: Fluids, Components, and System Effects
Basic Concepts
Design & Analysis of ASME Boiler and Pressure Vessel Components in the Creep Range