Abstract

The objective of this paper is to model the steady-state and dynamic operation of a pebble-bed-type high temperature gas-cooled reactor power plant using a system computational fluid dynamics (CFD) approach. System CFD codes are 1D network codes with embedded 2D or even 3D discretized component models that provide a good balance between accuracy and speed. In the method presented in this paper, valves, orifices, compressors, and turbines are modeled as lumped or 0D components, whereas pipes and heat exchangers are modeled as 1D discretized components. The reactor is modeled as 2D discretized system. A point kinetics neutronic model will predict the heat release in the reactor. Firstly, the layout of the power conversion system is discussed together with the major plant parameters. This is followed by a high level description of the system CFD approach together with a description of the various component models. The code is used to model the steady-state operation of the system. The results are verified by comparing them with detailed cycle analysis calculations performed with another code. The model is then used to predict the net power delivered to the shaft over a wide range of speeds from zero to full speed. This information is used to specify parameters for a proportional-integral-derivative controller that senses the speed of the power turbine and adjusts the generator power during the startup of the plant. The generator initially acts as a motor that drives the shaft and then changes over to a generator load that approaches the design point value as the speed of the shaft approaches the design speed. A full startup simulation is done to demonstrate the behavior of the plant during startup. This example demonstrates the application of a system CFD code to test control strategies. A load rejection example is considered where the generator load is suddenly dropped to zero from a full load condition. A controller senses the speed of the low pressure compressor/low pressure turbine shaft and then adjusts the opening of a bypass valve to keep the speed of the shaft constant at 60rps. The example demonstrates how detailed information on critical parameters such as turbine and reactor inlet temperatures, maximum fuel temperature, and compressor surge margin can be obtained during operating transients. System CFD codes is a powerful design tool that is indispensable in the design of complex power systems such as gas-cooled nuclear power plants.

1.
PBMR (Pty) Ltd.
Reactor Safety Analysis Report of the South-African Pebble-Bed Modular Reactor (PBMR), Rev. E, Centurion, South Africa.
2.
3.
Greyvenstein
,
G. P.
, and
Laurie
,
D. P.
, 2002, “
A Segregated CFD Approach to Pipe Network Analysis
,”
Int. J. Numer. Methods Eng.
0029-5981,
37
, pp.
3685
3705
.
4.
Greyvenstein
,
G. P.
, 2002, “
An Implicit Method for the Analysis of Transient Flows in Pipe Networks
,”
Int. J. Numer. Methods Eng.
0029-5981,
53
(
5
), pp.
1127
1143
.
5.
Greyvenstein
,
G. P.
,
Van Ravenswaay
,
J. P.
, and
Rousseau
,
P. G.
, 2002, “
Dynamic Modelling of Heat, Mass and Momentum Transfer in the Pebble Bed Modular Reactor
,” First International Conference on Heat Transfer, Fluid Mechanics and Thermodynamics (HEFAT 2002),
Kruger Park, South Africa
.
6.
Swamee
,
P. K.
, and
Jain
,
A. K.
, 1976, “
Explicit Equations for Pipe-Flow Problems
,”
J. Hydr. Div.
0044-796X,
102
(
5
), pp.
657
664
.
7.
Patankar
,
S. V.
, 1980,
Numerical Heat Transfer and Fluid Flow
,
McGraw-Hill
,
New York
.
8.
Rousseau
,
P. G.
, and
Greyvenstein
,
G. P.
, 2003, “
One-Dimensional Reactor Model for the Integrated Simulation of the PBMR Power Plant
,”
Proceedings of the First International Conference on Heat Transfer, Fluid Mechanics and Thermodynamics
,
Kruger Park, South Africa
, Apr. 8–10, 2002.
9.
Du Toit
,
C. G.
,
Rousseau
,
P. G.
,
Greyvenstein
,
G. P.
, and
Landman
,
W. A.
, 2005, “
A Systems CFD Model of a Packed Bed High Temperature Gas-Cooled Nuclear Reactor
,”
Int. J. Therm. Sci.
1290-0729,
45
, pp.
70
85
.
You do not currently have access to this content.