Ceramic matrix composites (CMCs) provide several benefits over metal blades including weight and increased temperature capability, and have the potential for increased engine performance by reduction of the cooling flow bled from the compressor and by allowing engines to run at higher turbine inlet temperatures. These CMC blades must be capable of surviving fatigue (high cycle and low cycle), creep, impact, and any tip rub events due to the engine missions or maneuvers that temporarily close blade tip/shroud clearances. As part of a cooperative research program between GE Aviation and the Ohio State University Gas Turbine Laboratory, OSU GTL, the response of a CMC stage 1 low-pressure turbine blade has been compared with the response of an equivalent metal turbine blade using the OSU GTL large spin-pit facility (LSPF) as the test vehicle. Load cells mounted on the casing wall, strain gages mounted on the airfoils, and other instrumentation are used to assess blade tip rub interactions with a 120-deg sector of a representative turbine stationary casing. The intent of this paper is to present the dynamic response of both the CMC and the metal blades with the turbine disk operating at design speed and with representative incursion rates and depths. Casing wear and blade tip wear are both characterized for several types of rub conditions including a light, medium, and heavy rub at room temperature. For each condition, the rub primary dynamic modes have been evaluated, and the corresponding blade tip loads have been calculated. The preliminary results suggest that a CMC blade has similar abilities to a metal blade during a rub event.
Skip Nav Destination
Article navigation
June 2015
Research-Article
Dynamic Response of a Metal and a CMC Turbine Blade During a Controlled Rub Event Using a Segmented Shroud
Nisrene Langenbrunner,
Nisrene Langenbrunner
GE Aviation
,Cincinnati, OH 45215
Search for other works by this author on:
Corso Padova,
Corso Padova
Gas Turbine Laboratory,
Ohio State University
,Columbus, OH 43235
Search for other works by this author on:
Jeffery Barton
Jeffery Barton
Gas Turbine Laboratory,
Ohio State University
,Columbus, OH 43235
Search for other works by this author on:
Nisrene Langenbrunner
GE Aviation
,Cincinnati, OH 45215
Matt Weaver
GE Aviation
,Cincinnati, OH 45215
Michael G. Dunn
Corso Padova
Gas Turbine Laboratory,
Ohio State University
,Columbus, OH 43235
Jeffery Barton
Gas Turbine Laboratory,
Ohio State University
,Columbus, OH 43235
Contributed by the Structures and Dynamics Committee of ASME for publication in the JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER. Manuscript received July 30, 2014; final manuscript received September 2, 2014; published online December 9, 2014. Editor: David Wisler.
J. Eng. Gas Turbines Power. Jun 2015, 137(6): 062504 (8 pages)
Published Online: June 1, 2015
Article history
Received:
July 30, 2014
Revision Received:
September 2, 2014
Online:
December 9, 2014
Citation
Langenbrunner, N., Weaver, M., Dunn, M. G., Padova, C., and Barton, J. (June 1, 2015). "Dynamic Response of a Metal and a CMC Turbine Blade During a Controlled Rub Event Using a Segmented Shroud." ASME. J. Eng. Gas Turbines Power. June 2015; 137(6): 062504. https://doi.org/10.1115/1.4028685
Download citation file:
Get Email Alerts
Heat Release Characteristics of a Volatile, Oxygenated, and Reactive Fuel in a Direct Injection Engine
J. Eng. Gas Turbines Power
Comprehensive Life Cycle Analysis of Diverse Hydrogen Production Routes and Application on a Hydrogen Engine
J. Eng. Gas Turbines Power
Related Articles
Transient Thermal Analysis and Viscoplastic Damage Model for Life Prediction of Turbine Components
J. Eng. Gas Turbines Power (April,2015)
Erosion in Gas-Turbine Grade Ceramic Matrix Composites
J. Eng. Gas Turbines Power (January,2019)
Design Considerations for Tip Clearance Control and Measurement on a Turbine Rainbow Rotor With Multiple Blade Tip Geometries
J. Eng. Gas Turbines Power (April,2017)
A Multiscale Approach for Nonlinear Dynamic Response Predictions With Fretting Wear
J. Eng. Gas Turbines Power (February,2017)
Related Proceedings Papers
Related Chapters
Outlook
Closed-Cycle Gas Turbines: Operating Experience and Future Potential
Basic Concepts
Analysis of ASME Boiler, Pressure Vessel, and Nuclear Components in the Creep Range
Basic Concepts
Design & Analysis of ASME Boiler and Pressure Vessel Components in the Creep Range