A fixed-geometry hybrid thrust bearing is investigated with three different supply orifice diameters, (1.63, 1.80, and 1.93 mm). The test rig uses a face-to-face thrust-bearing design, with the test bearing acting as the rotor loading mechanism. A hydraulic shaker applies the static axial load, which is reacted by a second (slave) thrust bearing. The rotor is supported radially by two water-lubricated fluid-film journal bearings and is attached to a 30.6 krpm motor via a high-speed coupling with very low axial stiffness. Thrust bearings are tested for a range of supply pressures (5.17, 10.34, and 17.34 bars), fluid film thicknesses, and speeds (7.5, 12.5, and 17.5 krpm). The water-lubricated test bearings have eight pockets, with feed orifices located centrally in each pocket. Experimental results are compared to predictions from a bulk-flow model, showing generally good agreement. Thrust-bearing inlet supply and inner radius flow rates all decreased with decreasing orifice diameters and bearing axial clearances. In most cases, the bearings with larger orifice diameters exhibit higher recess pressure ratios, operating clearances, and flow rates. An optimum hybrid thrust-bearing orifice diameter will depend on the conditions of individual applications. Larger orifices generally provide larger operating clearances and higher stiffnesses, but also require higher flow rates. For most applications, a compromise of bearing performance parameters will be desired. The test results and comparisons presented will aid in sizing orifice diameters for future hybrid thrust-bearing designs and in validating and improving models and predictions.
Skip Nav Destination
Article navigation
June 2019
Research-Article
Measurements Versus Predictions for a Hybrid (Hydrostatic Plus Hydrodynamic) Thrust Bearing for a Range of Orifice Diameters
Dara W. Childs,
Dara W. Childs
Leland T. Jordan Professor of Mechanical
Engineering,
Turbomachinery Laboratory Texas A&M
University,
College Station, TX 77845
Engineering,
Turbomachinery Laboratory Texas A&M
University,
College Station, TX 77845
Search for other works by this author on:
Paul Esser
Paul Esser
M.S. Mechanical Engineering,
Texas A&M University,
College Station, TX 77845
Texas A&M University,
College Station, TX 77845
Search for other works by this author on:
Dara W. Childs
Leland T. Jordan Professor of Mechanical
Engineering,
Turbomachinery Laboratory Texas A&M
University,
College Station, TX 77845
Engineering,
Turbomachinery Laboratory Texas A&M
University,
College Station, TX 77845
Paul Esser
M.S. Mechanical Engineering,
Texas A&M University,
College Station, TX 77845
Texas A&M University,
College Station, TX 77845
Manuscript received July 3, 2018; final manuscript received January 15, 2019; published online February 21, 2019. Editor: Jerzy T. Sawicki.
J. Eng. Gas Turbines Power. Jun 2019, 141(6): 061015 (12 pages)
Published Online: February 21, 2019
Article history
Received:
July 3, 2018
Revised:
January 15, 2019
Citation
Childs, D. W., and Esser, P. (February 21, 2019). "Measurements Versus Predictions for a Hybrid (Hydrostatic Plus Hydrodynamic) Thrust Bearing for a Range of Orifice Diameters." ASME. J. Eng. Gas Turbines Power. June 2019; 141(6): 061015. https://doi.org/10.1115/1.4042721
Download citation file:
Get Email Alerts
Cited By
Cooled Spray Technology for Particulate Reduction in a Heavy-Duty Engine
J. Eng. Gas Turbines Power
Prediction and Analysis of Transient Turbine Tip Clearance Using Long Short-Term Memory Neural Network
J. Eng. Gas Turbines Power
Gas Turbine's Role in Energy Transition
J. Eng. Gas Turbines Power (October 2024)
The Effect of Swirl Number on Lean Blow Out Limits of Lean Direct Injection Combustors
J. Eng. Gas Turbines Power (October 2024)
Related Articles
Static Characteristics of a Rectangular Hydrostatic Thrust Bearing With a Self-Controlled Restrictor Employing a Floating Disk
J. Tribol (April,1993)
A Water-Lubricated Hybrid Thrust Bearing: Measurements and Predictions of Static Load Performance
J. Eng. Gas Turbines Power (February,2017)
Static Load Performance of a Water-Lubricated Hydrostatic Thrust Bearing
J. Eng. Gas Turbines Power (June,2018)
Effects of Misalignment on Turbulent Flow Hybrid Thrust Bearings
J. Tribol (January,2002)
Related Proceedings Papers
Related Chapters
Hydrodynamic Lubrication
Design of Mechanical Bearings in Cardiac Assist Devices
Average Shaft Centerline Plots
Fundamentals of Rotating Machinery Diagnostics
Summary and Conclusions
Bearing Dynamic Coefficients in Rotordynamics: Computation Methods and Practical Applications