The Advanced Neutron Source (ANS) reactor was designed to provide a research tool with capabilities beyond those of any existing reactors. One portion of its state-of-the-art design required high velocity fluid flow through narrow channels between the fuel plates in the core. Experience with previous reactors had shown that fuel plate damage could occur if debris became lodged at the entrance to these channels. Such debris disrupts the fluid flow to the plate surfaces and could prevent adequate cooling of the fuel. Preliminary ANS designs addressed this issue by providing an unheated entrance length for each fuel plate so that any flow disruption would have time to recover before reaching the heated portions of the fuel plates further downstream. As part of the safety analysis, the adequacy of this unheated entrance length was assessed using both analytical models and experimental measurements. The Flow Blockage Test Facility (FBTF) was designed and built to conduct experiments in an environment closely matching the ANS channel geometry. The FBTF permitted careful measurements of both heat transfer and hydraulic parameters. In addition to these experimental efforts, a thin rectangular channel was modeled using the FLUENT computational fluid dynamics computer code. The numerical results were compared to the experimental data to benchmark the hydrodynamics of the model. After this comparison, the model was extended to include those elements of the safety analysis difficult to measure experimentally. These elements included the high wall heat flux pattern and variable fluid properties.
Skip Nav Destination
Article navigation
Research Papers
Effects of Partial Inlet Blockages on High-Velocity Flow Through a Thin Rectangular Duct: Experimental and Analytical Results
J. A. Crabtree,
J. A. Crabtree
Oak Ridge National Laboratory, PO Box 2008, Oak Ridge, TN 37831-6092
Search for other works by this author on:
D. K. Felde,
D. K. Felde
Oak Ridge National Laboratory, PO Box 2008, Oak Ridge, TN 37831-6092
Search for other works by this author on:
G. Farquharson,
G. Farquharson
Oak Ridge National Laboratory, PO Box 2008, Oak Ridge, TN 37831-6092
Search for other works by this author on:
J. E. Park
J. E. Park
Oak Ridge National Laboratory, PO Box 2008, Oak Ridge, TN 37831-6092
Search for other works by this author on:
T. K. Stovall
J. A. Crabtree
Oak Ridge National Laboratory, PO Box 2008, Oak Ridge, TN 37831-6092
D. K. Felde
Oak Ridge National Laboratory, PO Box 2008, Oak Ridge, TN 37831-6092
G. Farquharson
Oak Ridge National Laboratory, PO Box 2008, Oak Ridge, TN 37831-6092
J. E. Park
Oak Ridge National Laboratory, PO Box 2008, Oak Ridge, TN 37831-6092
J. Heat Transfer. Aug 1997, 119(3): 440-450 (11 pages)
Published Online: August 1, 1997
Article history
Received:
June 21, 1996
Revised:
April 25, 1997
Online:
December 5, 2007
Citation
Stovall, T. K., Crabtree, J. A., Felde, D. K., Farquharson, G., and Park, J. E. (August 1, 1997). "Effects of Partial Inlet Blockages on High-Velocity Flow Through a Thin Rectangular Duct: Experimental and Analytical Results." ASME. J. Heat Transfer. August 1997; 119(3): 440–450. https://doi.org/10.1115/1.2824117
Download citation file:
Get Email Alerts
Cited By
Entropic Analysis of the Maximum Output Power of Thermoradiative Cells
J. Heat Mass Transfer
Molecular Dynamics Simulations in Nanoscale Heat Transfer: A Mini Review
J. Heat Mass Transfer
Related Articles
Visualization and Analysis of Flow in an Offset Channel
J. Heat Transfer (November,1992)
Numerical Investigation of Flow Field and Heat Transfer in Cross-Corrugated Ducts
J. Heat Transfer (May,1999)
Heat Transfer Coefficient Enhancement With Perforated Baffles
J. Heat Transfer (August,1998)
Vortex Generator Induced Heat Transfer Augmentation Past a Rib in a Heated Duct Air Flow
J. Heat Transfer (February,1992)
Related Proceedings Papers
Related Chapters
Hydraulic Resistance
Heat Transfer & Hydraulic Resistance at Supercritical Pressures in Power Engineering Applications
Heat Transfer Enhancement by Using Nanofluids in Laminar Forced Convection Flows Considering Variable Properties
Proceedings of the 2010 International Conference on Mechanical, Industrial, and Manufacturing Technologies (MIMT 2010)
A Collection of Handy Hydraulic Formulas Based on an Industry-Standard Reference for Pressure Drop Calculations, Incompressible Fluid Flow in Piping and Ducts—Crane Technical Paper No. 410
Hydraulics, Pipe Flow, Industrial HVAC & Utility Systems: Mister Mech Mentor, Vol. 1