Direct cooling by means of jets and sprays has been considered as a solution to the problem of cooling of high power density electronic devices. Although both methods are capable of very high heat removal rates no criterion exists that helps one decide as to which one is preferable, when designing a cooling system for electronic applications. In this work, the results of an investigation of the performances of sprays and arrays of micro jets are reported. Experiments have been conducted using HAGO nozzles and orifice plates to create droplet sprays and arrays of micro jets, respectively. The liquid jets had diameters ranging from 69 to 250 μm and the pitches between the jets were 1, 2, and 3 mm. The test fluid was deionized water and the jet Reynolds number ranged between 43 and 3813. A comparison of heat transfer and pressure drop results obtained employing both sprays and jets has been carried out. The microjet arrays proved superior to the sprays since they required less pumping power per unit of power removed. A cooling module employing impinging jets was tested. Such a module would require three primary components: an orifice plate for forming jets or a nozzle to form the spray; a container to hold the nozzle, the heat source and the cooling liquid, which also serves as a heat exchanger to the ambient; and a pump which recirculates the coolant. A fan could be used to improve the heat transfer to the ambient, and it would allow the use of a smaller container. An impinging jets cooling module has been designed and tested. Heat fluxes as high as 300 W/cm2 at 80°C surface temperature could be removed using a system which includes a 4×6 array of microjets of water of 140 μm diameter impinging on a diode 5.0×8.7 mm2.
Skip Nav Destination
e-mail: vdhir@seas.ucla.edu
Article navigation
Article
A Comparative Study of Cooling of High Power Density Electronics Using Sprays and Microjets
Matteo Fabbri,
Matteo Fabbri
Mechanical and Aerospace Engineering Department, Henry Samueli School of Engineering and Applied Science, University of California Los Angeles, 420 Westwood Plaza, Los Angeles, CA 90095
Search for other works by this author on:
Shanjuan Jiang,
Shanjuan Jiang
Mechanical and Aerospace Engineering Department, Henry Samueli School of Engineering and Applied Science, University of California Los Angeles, 420 Westwood Plaza, Los Angeles, CA 90095
Search for other works by this author on:
Vijay K. Dhir
e-mail: vdhir@seas.ucla.edu
Vijay K. Dhir
Mechanical and Aerospace Engineering Department, Henry Samueli School of Engineering and Applied Science, University of California Los Angeles, 420 Westwood Plaza, Los Angeles, CA 90095
Search for other works by this author on:
Matteo Fabbri
Mechanical and Aerospace Engineering Department, Henry Samueli School of Engineering and Applied Science, University of California Los Angeles, 420 Westwood Plaza, Los Angeles, CA 90095
Shanjuan Jiang
Mechanical and Aerospace Engineering Department, Henry Samueli School of Engineering and Applied Science, University of California Los Angeles, 420 Westwood Plaza, Los Angeles, CA 90095
Vijay K. Dhir
Mechanical and Aerospace Engineering Department, Henry Samueli School of Engineering and Applied Science, University of California Los Angeles, 420 Westwood Plaza, Los Angeles, CA 90095
e-mail: vdhir@seas.ucla.edu
Contributed by the Heat Transfer Division for publication in the JOURNAL OF HEAT TRANSFER. Manuscript received by the Heat Transfer Division May 12, 2004; revision received July 24, 2004. Associate Editor: C. Amon.
J. Heat Transfer. Jan 2005, 127(1): 38-48 (11 pages)
Published Online: February 15, 2005
Article history
Received:
May 12, 2004
Revised:
July 24, 2004
Online:
February 15, 2005
Citation
Fabbri , M., Jiang , S., and Dhir, V. K. (February 15, 2005). "A Comparative Study of Cooling of High Power Density Electronics Using Sprays and Microjets ." ASME. J. Heat Transfer. January 2005; 127(1): 38–48. https://doi.org/10.1115/1.1804205
Download citation file:
Get Email Alerts
Cited By
Entropic Analysis of the Maximum Output Power of Thermoradiative Cells
J. Heat Mass Transfer
Molecular Dynamics Simulations in Nanoscale Heat Transfer: A Mini Review
J. Heat Mass Transfer
Related Articles
Microelectromechanical System-Based Evaporative Thermal Management of High Heat Flux Electronics
J. Heat Transfer (January,2005)
The Effect of Dissolving Salts in Water Sprays Used for Quenching a Hot Surface: Part 2—Spray Cooling
J. Heat Transfer (April,2003)
Heat Transfer of Impacting Water Mist on High Temperature Metal Surfaces
J. Heat Transfer (February,2003)
On the Scalability of Liquid Microjet Array Impingement Cooling for Large Area Systems
J. Heat Transfer (June,2011)
Related Proceedings Papers
Related Chapters
Numerical Simulation of Nucleate Spray Cooling: Effect of Droplet Impact on Bubble Growth and Heat Transfer in a Thin Liquid Film
Inaugural US-EU-China Thermophysics Conference-Renewable Energy 2009 (UECTC 2009 Proceedings)
A New Boom Mechanism Design for Corn Sprayer
International Conference on Mechanical Engineering and Technology (ICMET-London 2011)
Fuel Nozzle Geometry Effects on Cavitation and Spray Behavior at Diesel Engine Conditions
Proceedings of the 10th International Symposium on Cavitation (CAV2018)