Heat transfer to objects immersed in a fluidized bed has been studied extensively across a relatively large range of geometries, though most work has looked at cylinders, a geometry important in power generation fluidized bed applications. As the power generation industry has been the primary stimulant to fluidized bed heat transfer research, very little information is available regarding geometries significant in heat treating applications. In this work, heat transfer to thin flat strips immersed in a fluidized bed is examined. This geometry is important in the steel strap manufacturing industry where many manufacturers use environmentally damaging molten lead baths to heat-treat their product. In order to determine the feasibility of a fluidized bed heat treating system as an alternative to the more hazardous lead-based process, an experimental investigation has been conducted in which Nusselt number data for flat strips with widths in the range of 6.35–25.4 mm are obtained using a laboratory-scale fluidized bed (310 mm diameter). Aluminum oxide sand particles in the range of dp=145330μm (50–90 grit) are used as the fluidized media within the fluidized operating range from 0.15Gmf to approximately 10Gmf. The strip orientation angle θo was also varied to establish the position from which maximum heat transfer is obtained. It was found that a decrease in particle diameter, an increase in fluidizing rate, and an increase in sample diameter resulted in an increase in Nusselt number. It was also observed that for the smaller samples tested, a maximum Nusselt number plateau was reached, at approximately G/Gmf=2.5. Finally, it was shown that an increase in θo (from 0 deg to 90 deg) resulted in an increase in Nusselt number. A correlation for the maximum Nusselt number was developed, providing excellent agreement within ±15%.

1.
Saxena
,
S. C.
, 1989, “
Heat Transfer Between Immersed Surfaces and Gas-Fluidized Beds
,”
Adv. Heat Transfer
0065-2717,
19
, pp.
97
190
.
2.
Li
,
H. -S.
,
Qian
,
R. -Z.
,
Huang
,
W. -D.
, and
Bi
,
K. -J.
, 1993, “
An Investigation on Instantaneous Local Heat Transfer Coefficients in High-Temperature Fluidized Beds—I. Experimental Results
,”
Int. J. Heat Mass Transfer
0017-9310,
36
(
18
), pp.
4389
4395
.
3.
Khan
,
T.
, and
Turton
,
R.
, 1992, “
The Measurements of Instantaneous Heat Transfer Coefficient Around the Circumference of a Tube Immersed in a High Temperature Fluidized Bed
,”
Int. J. Heat Mass Transfer
0017-9310,
35
(
12
), pp.
3397
3406
.
4.
Karamavruc
,
A. I.
, and
Clark
,
N. N.
, 1996, “
A Correction Factor for One-Dimensional Heat Transfer Coefficients Around a Horizontal Tube in a Fluidized Bed
,”
Powder Technol.
0032-5910,
86
, pp.
209
217
.
5.
Friedman
,
J.
,
Koundakjian
,
P.
,
Naylor
,
D.
, and
Rosero
,
D.
, 2006, “
Heat Transfer to Small Horizontal Cylinders Immersed in a Fluidized Bed
,”
ASME J. Heat Transfer
0022-1481,
128
, pp.
984
989
.
6.
Baskakov
,
A. P.
,
Berg
,
B. V.
,
Vitt
,
O. K.
,
Filippovsky
,
N. F.
,
Kirakosyan
,
V. A.
,
Goldobin
,
J. M.
, and
Maskaev
,
V. K.
, 1973, “
Heat Transfer to Objects Immersed in Fluidized Beds
,”
Powder Technol.
0032-5910,
8
, pp.
273
282
.
7.
Ahmed
,
G. R.
, and
Yovanovich
,
M. M.
, 1997, “
Experimental Study of Forced Convection From Isothermal Circular and Square Cylinders and Toroids
,”
ASME J. Heat Transfer
0022-1481,
119
, pp.
70
78
.
8.
Koundakjian
,
P.
, 2002, “
Heat Transfer to Small Cylinders Immersed in a Fluidized Bed Heat Treating Furnace
,” MS thesis, University of Waterloo, Waterloo, ON, Canada.
9.
DeWitt
,
D. P.
, and
Incropera
,
F. P.
, 2002,
Fundamentals of Heat and Mass Transfer
, 5th ed.,
Wiley
,
New York
.
10.
Grewal
,
N. S.
, and
Saxena
,
S. C.
, 1980, “
Heat Transfer Between a Horizontal Tube and a Gas-Solid Fluidized Bed
,”
Int. J. Heat Mass Transfer
0017-9310,
23
, pp.
1505
1519
.
11.
Rasouli
,
S.
,
Golriz
,
M. R.
, and
Hamidi
,
A. A.
, 2005, “
Effect of Annular Fins on Heat Transfer of a Horizontal Immersed Tube in Bubbling Fluidized Beds
,”
Powder Technol.
0032-5910,
154
, pp.
9
13
.
12.
Botterill
,
J. S. M.
, 1975,
Fluid-Bed Heat Transfer: Gas-Fluidized Bed Behaviour and Its Influence on Bed Thermal Properties
,
Academic
,
London
.
13.
Doherty
,
J. A.
,
Verma
,
R. S.
,
Shrivastava
,
S.
, and
Saxena
,
S. C.
, 1986, “
Heat Transfer From Immersed Horizontal Tubes of Different Diameter in a Gas Fluidized Bed
,”
Energy
0360-5442,
11
(
8
), pp.
773
783
.
14.
Glass
,
D. H.
, and
Harrison
,
D.
, 1964, “
Flow Patterns Near a Solid Obstacle in a Fluidized Bed
,”
Chem. Eng. Sci.
0009-2509,
19
, pp.
1001
1002
.
15.
Howard
,
J. R.
, 1989,
Fluidized Bed Technology: Principles and Applications
,
Adam Hilger
,
Bristol, New York
.
16.
Holman
,
J. P.
, 1989,
Experimental Methods for Engineers
, 5th ed.,
McGraw-Hill
,
New York
.
17.
Molerus
,
O.
, and
Wirth
,
K. E.
, 1997,
Heat Transfer in Fluidized Beds
,
Chapman and Hall
,
London
.
You do not currently have access to this content.