In a heat pipe, operating fluid saturates wick structures system and establishes a capillary-driven circulation loop for heat transfer. Thus, the thermophysical properties of the operating fluid inevitably impact the transitions of phase-change mode and the capability of heat transfer, which determine both the design and development of the associated heat pipe systems. This article investigates the effect of liquid properties on phase-change heat transfer. Two different copper wick structures, cubic and cylindrical in cross section, 340 μm in height and 150 μm in diameter or width, are fabricated using an electroplating technique. The phase-change phenomena inside these wick structures are observed at various heat fluxes. The corresponding heat transfer characteristics are measured for three different working liquids: water, ethanol, and Novec 7200. Three distinct modes of the phase-change process are identified: (1) evaporation on liquid–vapor interface, (2) nucleate boiling with interfacial evaporation, and (3) boiling enhanced interface evaporation. Transitions between the three modes depend on heat flux and liquid properties. In addition to the mode transition, liquid properties also dictate the maximum heat flux and the heat transfer coefficient. A quantitative characterization shows that the maximum heat flux scales with Merit number, a dimensionless number connecting liquid density, surface tension, latent heat of vaporization, and viscosity. The heat transfer coefficient, on the other hand, is dictated by the thermal conductivity of the liquid. A complex interaction between the mode transition and liquid properties is reflected in Novec 7200. In spite of having the lowest thermal conductivity among the three liquids, an early transition to the mode of the boiling enhanced interface evaporation leads to a higher heat transfer coefficient at low heat flux.
Skip Nav Destination
Article navigation
Research-Article
Effect of Liquid Properties on Phase-Change Heat Transfer in Porous Wick Structures
Steve Q. Cai,
Steve Q. Cai
Teledyne Scientific & Image Company,
1049 Camino Dos Rios,
Thousand Oaks, CA 91360
e-mail: qingjun.cai@teledyne.com
1049 Camino Dos Rios,
Thousand Oaks, CA 91360
e-mail: qingjun.cai@teledyne.com
Search for other works by this author on:
Avijit Bhunia
Avijit Bhunia
Teledyne Scientific & Image Company,
1049 Camino Dos Rios,
Thousand Oaks, CA 91360
1049 Camino Dos Rios,
Thousand Oaks, CA 91360
Search for other works by this author on:
Steve Q. Cai
Teledyne Scientific & Image Company,
1049 Camino Dos Rios,
Thousand Oaks, CA 91360
e-mail: qingjun.cai@teledyne.com
1049 Camino Dos Rios,
Thousand Oaks, CA 91360
e-mail: qingjun.cai@teledyne.com
Avijit Bhunia
Teledyne Scientific & Image Company,
1049 Camino Dos Rios,
Thousand Oaks, CA 91360
1049 Camino Dos Rios,
Thousand Oaks, CA 91360
Contributed by the Heat Transfer Division of ASME for publication in the JOURNAL OF HEAT TRANSFER. Manuscript received December 15, 2014; final manuscript received October 21, 2015; published online November 24, 2015. Assoc. Editor: Amitabh Narain.
J. Heat Transfer. Mar 2016, 138(3): 031504 (7 pages)
Published Online: November 24, 2015
Article history
Received:
December 15, 2014
Revised:
October 21, 2015
Citation
Cai, S. Q., and Bhunia, A. (November 24, 2015). "Effect of Liquid Properties on Phase-Change Heat Transfer in Porous Wick Structures." ASME. J. Heat Transfer. March 2016; 138(3): 031504. https://doi.org/10.1115/1.4031929
Download citation file:
Get Email Alerts
Cited By
Entropic Analysis of the Maximum Output Power of Thermoradiative Cells
J. Heat Mass Transfer
Molecular Dynamics Simulations in Nanoscale Heat Transfer: A Mini Review
J. Heat Mass Transfer
Related Articles
Numerical Simulation of Evaporating Two-Phase Flow in a High-Aspect-Ratio Microchannel with Bends
J. Heat Transfer (August,2017)
Nucleate Boiling Comparison between Teflon-Coated Plain Copper and Cu-HTCMC in Water
J. Heat Transfer (August,2018)
Enhanced Heat Transfer in Biporous Wicks in the Thin Liquid Film Evaporation and Boiling Regimes
J. Heat Transfer (October,2012)
Utilization of Advanced Working Fluids With Biporous Evaporators
J. Thermal Sci. Eng. Appl (June,2011)
Related Proceedings Papers
Related Chapters
Thermal Design Guide of Liquid Cooled Systems
Thermal Design of Liquid Cooled Microelectronic Equipment
Scope of Section I, Organization, and Service Limits
Power Boilers: A Guide to the Section I of the ASME Boiler and Pressure Vessel Code, Second Edition
Liquid Cooled Systems
Thermal Management of Telecommunication Equipment, Second Edition