Near-field thermophotovoltaic (NFTPV) devices have received much attention lately as an alternative energy harvesting system, whereby a heated emitter exchanges super-Planckian thermal radiation with a photovoltaic (PV) cell to generate electricity. This work describes the use of a grating structure to enhance the power throughput of NFTPV devices, while increasing the energy conversion efficiency by ensuring that a large portion of the radiation entering the PV cell is above the band gap. The device contains a high-temperature tungsten grating that radiates photons to a room-temperature In0.18Ga0.82Sb PV cell through a vacuum gap of several tens of nanometers. Scattering theory is used along with the rigorous coupled-wave analysis (RCWA) to calculate the radiation energy exchange between the grating emitter and the TPV cell. A parametric study is performed by varying the grating depth, period, and ridge width in the range that can be fabricated using available fabrication technologies. It is found that the power output can be increased by 40% while improving the efficiency from 29.9% to 32.0% with a selected grating emitter as compared to the case of a flat tungsten emitter. Reasons for the enhancement are found to be due to the enhanced energy transmission coefficient close to the band gap. This work shows a possible way of improving NFTPV and sheds light on how grating structures interact with thermal radiation at the nanoscale.
Skip Nav Destination
Article navigation
Research-Article
A Computational Simulation of Using Tungsten Gratings in Near-Field Thermophotovoltaic Devices
J. I. Watjen,
J. I. Watjen
George W. Woodruff School of
Mechanical Engineering,
Georgia Institute of Technology,
Atlanta, GA 30332
Mechanical Engineering,
Georgia Institute of Technology,
Atlanta, GA 30332
Search for other works by this author on:
X. L. Liu,
X. L. Liu
George W. Woodruff School of
Mechanical Engineering,
Georgia Institute of Technology,
Atlanta, GA 30332;
Mechanical Engineering,
Georgia Institute of Technology,
Atlanta, GA 30332;
School of Energy and Power Engineering,
Nanjing University of Aeronautics and Astronautics,
Nanjing 210016, China
Nanjing University of Aeronautics and Astronautics,
Nanjing 210016, China
Search for other works by this author on:
B. Zhao,
B. Zhao
George W. Woodruff School of Mechanical Engineering,
Georgia Institute of Technology,
Atlanta, GA 30332
Georgia Institute of Technology,
Atlanta, GA 30332
Search for other works by this author on:
Z. M. Zhang
Z. M. Zhang
Fellow ASME
George W. Woodruff School of
Mechanical Engineering,
Georgia Institute of Technology,
Atlanta, GA 30332
e-mail: zhuomin.zhang@me.gatech.edu
George W. Woodruff School of
Mechanical Engineering,
Georgia Institute of Technology,
Atlanta, GA 30332
e-mail: zhuomin.zhang@me.gatech.edu
Search for other works by this author on:
J. I. Watjen
George W. Woodruff School of
Mechanical Engineering,
Georgia Institute of Technology,
Atlanta, GA 30332
Mechanical Engineering,
Georgia Institute of Technology,
Atlanta, GA 30332
X. L. Liu
George W. Woodruff School of
Mechanical Engineering,
Georgia Institute of Technology,
Atlanta, GA 30332;
Mechanical Engineering,
Georgia Institute of Technology,
Atlanta, GA 30332;
School of Energy and Power Engineering,
Nanjing University of Aeronautics and Astronautics,
Nanjing 210016, China
Nanjing University of Aeronautics and Astronautics,
Nanjing 210016, China
B. Zhao
George W. Woodruff School of Mechanical Engineering,
Georgia Institute of Technology,
Atlanta, GA 30332
Georgia Institute of Technology,
Atlanta, GA 30332
Z. M. Zhang
Fellow ASME
George W. Woodruff School of
Mechanical Engineering,
Georgia Institute of Technology,
Atlanta, GA 30332
e-mail: zhuomin.zhang@me.gatech.edu
George W. Woodruff School of
Mechanical Engineering,
Georgia Institute of Technology,
Atlanta, GA 30332
e-mail: zhuomin.zhang@me.gatech.edu
1Corresponding author.
Presented at the 2016 ASME 5th Micro/Nanoscale Heat & Mass Transfer International Conference. Paper No. MNHMT2016-6632.
Contributed by the Heat Transfer Division of ASME for publication in the JOURNAL OF HEAT TRANSFER. Manuscript received April 15, 2016; final manuscript received November 21, 2016; published online February 14, 2017. Assoc. Editor: Chun Yang.
J. Heat Transfer. May 2017, 139(5): 052704 (8 pages)
Published Online: February 14, 2017
Article history
Received:
April 15, 2016
Revised:
November 21, 2016
Citation
Watjen, J. I., Liu, X. L., Zhao, B., and Zhang, Z. M. (February 14, 2017). "A Computational Simulation of Using Tungsten Gratings in Near-Field Thermophotovoltaic Devices." ASME. J. Heat Transfer. May 2017; 139(5): 052704. https://doi.org/10.1115/1.4035356
Download citation file:
Get Email Alerts
Cited By
Aircraft Ducted Heat Exchanger Aerodynamic Shape and Thermal Optimization
J. Heat Mass Transfer
A Simplified Thermal Hydraulic Model for Solid Pin-Fueled Molten Salt Reactors Under Low-Flow Accident Scenarios
J. Heat Mass Transfer (December 2024)
Effect of Forced Convection Heat Transfer on Vapor Quality in Subcooled Flow Boiling
J. Heat Mass Transfer (December 2024)
Related Articles
Manipulation of Thermal Emission by Use of Micro and Nanoscale Structures
J. Heat Transfer (March,2012)
A Monochrome Light-Emitting Diode Moiré Deflectometry Technique for Two-Dimensional Temperature Measurement
J. Heat Transfer (October,2014)
Scanning Grating Microinterferometer for MEMS Metrology
J. Manuf. Sci. Eng (November,2004)
Solar Thermophotovoltaic Converters Based on Tungsten Emitters
J. Sol. Energy Eng (August,2007)
Related Proceedings Papers
Related Chapters
Influence of Grating Parameter on Diffraction Efficiency of Transmission Volume Bragg Grating
International Conference on Instrumentation, Measurement, Circuits and Systems (ICIMCS 2011)
Experimental Research on Fiber Grating Sensor Acoustic Emission Detection of Rock Material Specimen Failure
Geological Engineering: Proceedings of the 1 st International Conference (ICGE 2007)
Electronic Properties of a Two-Dimensional Ring-Shaped Kronig-Penney Lattice with a Positional Disorder
International Conference on Mechanical and Electrical Technology, 3rd, (ICMET-China 2011), Volumes 1–3