In this paper, the results of experiments conducted to investigate the friction coefficient existing at a brass-steel interface are presented. The research discussed here is the second of a two-part study on the size effects in friction conditions that exist during microextrusion. In the regime of dimensions of the order of a few hundred microns, these size effects tend to play a significant role in affecting the characteristics of microforming processes. Experimental results presented in the previous companion paper have already shown that the friction conditions obtained from comparisons of experimental results and numerical models show a size effect related to the overall dimensions of the extruded part, assuming material response is homogeneous. Another interesting observation was made when extrusion experiments were performed to produce submillimeter sized pins. It was noted that pins fabricated from large grain-size material $(211μm)$ showed a tendency to curve, whereas those fabricated from billets having a small grain size $(32μm)$, did not show this tendency. In order to further investigate these phenomena, it was necessary to segregate the individual influences of material response and interfacial behavior on the microextrusion process, and therefore, a series of frictional experiments was conducted using a stored-energy Kolsky bar. The advantage of the Kolsky bar method is that it provides a direct measurement of the existing interfacial conditions and does not depend on material deformation behavior like other methods to measure friction. The method also provides both static and dynamic coefficients of friction, and these values could prove relevant for microextrusion tests performed at high strain rates. Tests were conducted using brass samples of a small grain size $(32μm)$ and a large grain size $(211μm)$ at low contact pressure $(22MPa)$ and high contact pressure $(250MPa)$ to see whether there was any change in the friction conditions due to these parameters. Another parameter that was varied was the area of contact. Static and dynamic coefficients of friction are reported for all the cases. The main conclusion of these experiments was that the friction coefficient did not show any significant dependence on the material grain size, interface pressure, or area of contact.

1.
Kinsey
,
B. L.
,
Parasiz
,
S.
,
Onyancha
,
R.
,
Ehmann
,
K.
,
Espinosa
,
H.
,
Liu
,
W. K.
,
Mori
,
L. F.
,
Krishnan
,
N.
, and
Li
,
M.
, 2006, “
Investigation of Deformation, Process Model, and Frictional Size Effects During Microforming
,”
Proc. of 2006 NSF Design, Service, and Manufacturing Grantees and Research Conference
, St. Louis, Sept.
National Science Foundation
.
2.
Krishnan
,
N.
,
Cao
,
J.
, and
Dohda
,
K.
, 2007, “
Study of the Size Effects and Friction Conditions in Micro-Extrusion—Part I: Micro-Extrusion Experiments and Analysis
,”
ASME J. Manuf. Sci. Eng.
1087-1357,
129
, pp.
669
676
.
3.
Wang
,
W.
,
Wagoner
,
R. H.
, and
Wang
,
X. J.
, 1996, “
Measurement of Friction Under Sheet Forming Conditions
,”
Metall. Mater. Trans. A
1073-5623,
27
(
12
), pp.
3971
3981
.
4.
Davim
,
J. P.
, 2000, “
An Experimental Study of the Tribological Behaviour of the Brass/Steel Pair
,”
J. Mater. Process. Technol.
0924-0136,
100
(
1–3
), pp.
273
277
.
5.
Kim
,
D. E.
, and
Hwang
,
D. H.
, 1998, “
Experimental Investigation of the Influence of Machining Condition on the Contact Sliding Behavior of Metals
,”
ASME J. Manuf. Sci. Eng.
1087-1357,
120
(
2
), pp.
395
400
.
6.
Ogawa
,
K.
, 1997, “
Impact Friction Test Method by Applying Stress Wave
,”
Exp. Mech.
0014-4851,
37
(
4
), pp.
398
402
.
7.
Sofuoglu
,
H.
,
Gedikli
,
H.
, and
Rasty
,
J.
, 2001, “
Determination of Friction Coefficient by Employing the Ring Compression Test
,”
ASME J. Eng. Mater. Technol.
0094-4289,
123
(
3
), pp.
338
348
.
8.
Blau
,
P. J.
, 2002, “
Appendix: Static and Kinetic Friction Coefficients for Selected Materials
,”
P. J.
Blau
, ed.,
ASM Handbook
, 4th ed.,
ASM International
,
Materials Park, OH
, Vol.
18
.
9.
Geiger
,
M.
,
Messner
,
A.
,
Engel
,
U.
,
Kals
,
R.
, and
Vollertsen
,
F.
, 1995, “
Design of Microforming Processes—Fundamentals, Material Data and Friction Behavior
,”
Proc. of 9th International Cold Forging Congress
,
Solihull
,
UK
, May 22–26, pp.
155
163
.
10.
Espinosa
,
H. D.
,
Patanella
,
A. J.
, and
Fischer
,
M.
, 2000, “
A Novel Dynamic Friction Experiment Using a Modified Kolsky Bar Apparatus
,”
Exp. Mech.
0014-4851,
40
(
2
):
138
153
.
11.
Espinosa
,
H. D.
,
Patanella
,
A. J.
, and
Fischer
,
M.
, 2000, “
Dynamic Friction Measurements at Sliding Velocities Representative of High-Speed Machining Processes
,”
ASME J. Tribol.
0742-4787,
122
(
4
), pp.
834
848
.
12.
Zhang
,
H.
,
Patanella
,
A. J.
,
Espinosa
,
H. D.
, and
Pae
,
K. D.
, 1999, “
Dynamic Friction of Nano-Materials
,”
Proc. of APS—Shock Compression of Condensed Matter
, Salt Lake City, July,
M. D.
Furnish
,
L. C.
Chhabildas
, and
R. S.
Hixon
, ed.,
American Institute of Physics
,
Melville, NY
.
13.
Rajagopalan
,
S.
, and
Prakash
,
V.
, 1999, “
A Modified Torsional Kolsky Bar for Investigating Dynamic Friction
,”
Exp. Mech.
0014-4851,
39
(
4
), pp.
295
303
.
14.
Larsen-Basse
,
J.
, 1992, “
Basic Theory of Solid Friction
,”
ASM Handbook
, 4th ed.,
P. J.
Blau
, ed.,
ASM International
,
Materials Park, OH
, Vol.
18
.
15.
Wilcoxon
,
F.
, 1945, “
Individual Comparisons by Ranking Methods
,”
Biometrics Bull.
,
1
(
6
), pp.
80
83
.
16.
Student
, 1908, “
The Probable Error of a Mean
,”
Biometrika
0006-3444,
6
(
1
), pp.
1
25
.
17.
Behrens
,
W. V.
, 1929, “
Ein Beitrag Zur Fehlerberechnung Bei Wenigen Beobachtungen
,”
Landwirtschaftliche Jahrbücher
,
68
, pp.
807
837
.
18.
Fisher
,
R. A.
, 1935, “
The Fiducial Argument in Statistical Inference
,”
Ann. Eugenics
,
6
, pp.
391
398
.
19.
Tukey
,
J. W.
, 1977,
Exploratory Data Analysis
,
,
.
20.
De Gee
,
A. W. J.
, and
Zaat
,
J. H.
, 1962, “
Wear of Copper Alloys Against Steel in Oxygen and Argon
,”
Wear
0043-1648,
5
(
4
), pp.
257
274
.
21.
Lancaster
,
J. K.
, 1963,
Proc. R. Soc. London, Ser. A
1364-5021,
273
, p.
466
.
22.
Ludema
,
K. C.
, 2002, “
Sliding and Adhesive Wear
,”
ASM Handbook
, 4th ed.,
P. J.
Blau
,
ASM International
,
Materials Park, OH
, Vol.
18
.
23.
Cao
,
J.
,
Krishnan
,
N.
,
Wang
,
Z.
,
Luand
,
H.
,
Liu
,
W. K.
, and
Swanson
,
A.
, 2004, “
Microforming—Experimental Investigation of the Extrusion Process for Micropins and Its Numerical Simulation Using RKEM
,”
ASME J. Manuf. Sci. Eng.
1087-1357,
126
(
4
), pp.
642
652
.
24.
Krishnan
,
N.
,
Cao
,
J.
,
Kinsey
,
B.
,
Parasiz
,
S.
, and
Li
,
M.
, 2005, “
Investigation of Deformation Characteristics of Micropins Fabricated Using Microextrusion
,”
ASME International Mechanical Engineering Conference and Exposition
, Orlando, Nov. 5–11
ASME
, New York.
You do not currently have access to this content.