The GI (graded-index) POFs (Plastic optical fibers), which has been proven to reach distances as long as 1 km at 1.25 Gb/s has a relatively low numerical aperture . Therefore, the efficient coupling of GI POFs to the light source has become critical to the power budget in the system. Efficient coupling for a POFs system normally involves either a separate lens or the direct formation of the lens at the end of the fiber. Forming the lens-like structure directly on the fiber end is preferred for simplicity of fabrication and packaging, such as polishing and fusion, combine different fibers with the cascaded fiber method and hydroflouride (HF) chemical etching. These approaches are well established, but applicable only to glass. Optical assembly architecture for multichannel fibers and optical devices is critical to optical fiber interconnections. Multichannel fiber-pigtail laser diode (LD) modules have potential for supporting higher data throughput and longer transmission distances. However, to be of practical use, these modules must be more precise. This work proposes and manufactures lensed plastic optical fibers (LPOF) array. This novel manipulation can be utilized to fabricate an aspherical lens on a fiber array after the UV curing of the photo-sensitive polymer; the coupling efficiency (CE) is increased and exceeds 47% between the LD array and the fiber array.
Skip Nav Destination
Article navigation
June 2011
Research Papers
Fabrication of Lensed Plastic Optical Fiber Array Using Electrostatic Force
Jhong-Bin Huang,
Jhong-Bin Huang
Department of Mechanical and Electro-Mechanical Engineering, National Sun Yat-Sen University
, 70 Lien-hai Road, Kaohsiung 804, Taiwan
, R.O.C.
Search for other works by this author on:
Che-Hsin Lin,
Che-Hsin Lin
Department of Mechanical and Electro-Mechanical Engineering, National Sun Yat-Sen University
, 70 Lien-hai Road, Kaohsiung 804, Taiwan
, R.O.C.
Search for other works by this author on:
Chin-Lung Chen,
Chin-Lung Chen
Department of Mechanical and Electro-Mechanical Engineering, National Sun Yat-Sen University
, 70 Lien-hai Road, Kaohsiung 804, Taiwan
, R.O.C.
Search for other works by this author on:
Wood-Hi Cheng
Wood-Hi Cheng
Senior Member IEEE, Fellow, OSA
Department of Mechanical and Electro-Mechanical Engineering, National Sun Yat-Sen University
, 70 Lien-hai Road, Kaohsiung 804, Taiwan
, R.O.C.
Search for other works by this author on:
Jhong-Bin Huang
Department of Mechanical and Electro-Mechanical Engineering, National Sun Yat-Sen University
, 70 Lien-hai Road, Kaohsiung 804, Taiwan
, R.O.C.
Che-Hsin Lin
Department of Mechanical and Electro-Mechanical Engineering, National Sun Yat-Sen University
, 70 Lien-hai Road, Kaohsiung 804, Taiwan
, R.O.C.
Chin-Lung Chen
Department of Mechanical and Electro-Mechanical Engineering, National Sun Yat-Sen University
, 70 Lien-hai Road, Kaohsiung 804, Taiwan
, R.O.C.
Wood-Hi Cheng
Senior Member IEEE, Fellow, OSA
Department of Mechanical and Electro-Mechanical Engineering, National Sun Yat-Sen University
, 70 Lien-hai Road, Kaohsiung 804, Taiwan
, R.O.C.J. Manuf. Sci. Eng. Jun 2011, 133(3): 031016 (6 pages)
Published Online: June 16, 2011
Article history
Received:
September 17, 2010
Revised:
April 28, 2011
Online:
June 16, 2011
Published:
June 16, 2011
Citation
Tseng, Y., Huang, J., Lin, C., Chen, C., and Cheng, W. (June 16, 2011). "Fabrication of Lensed Plastic Optical Fiber Array Using Electrostatic Force." ASME. J. Manuf. Sci. Eng. June 2011; 133(3): 031016. https://doi.org/10.1115/1.4004204
Download citation file:
Get Email Alerts
Cited By
Special Issue on the State-of-the-Art in Japanese Manufacturing Research
J. Manuf. Sci. Eng
A Review of Advanced Roll-to-Roll Manufacturing: System Modeling and Control
J. Manuf. Sci. Eng (April 2025)
Related Articles
Erratum: "Investigation of Steady-State Drawing Force and Heat
Transfer in Polymer Optical Fiber Manufacturing" [Journal of Heat Transfer,
2004, 126 (2), pp. 236–243]
J. Heat Transfer (August,2004)
Designing an Optical Bendloss Sensor for Clinical ForcMeasurement
J. Med. Devices (June,2009)
Lensed Plastic Optical Fiber with a Convexo-Concave Fiber Endface for Coupling Laser Diodes With Plastic Optical Fiber
J. Manuf. Sci. Eng (August,2011)
Fiber Optics Based Jet Engine Augmenter Viewing System
J. Eng. Gas Turbines Power (April,1989)
Related Proceedings Papers
Related Chapters
Electrostatic Technology for Control of Dust and Hydrocarbon Vapors in High Power Laser Systems
Laser Induced Damage in Optical Materials: 1981
Motion of Charged Bodies in an Electric Field
Dynamics of Particles and Rigid Bodies: A Self-Learning Approach
Structure, Properties, and Applications of Plastics
Introduction to Plastics Engineering