With the increased application of micromachining, including micromilling and microdrilling, the need to develop accurate models for machining at the microscale has been recognized. In particular, the crystallographic effects that are generally neglected in the macroscale cutting models must be incorporated into the micromachining models. Diamond turning and mechanical nanomanufacturing techniques also require an understanding of crystallographic effects during material removal. This work presents a rate-sensitive plasticity-based machining (RSPM) model that is used to determine the specific energies (and thus forces) for orthogonal cutting of face-centered cubic (fcc) single-crystals. The RSPM model uses kinematics and geometry of orthogonal cutting for an ideally sharp cutting edge. The total power is expressed in terms of the plastic power, which is spent for shearing the material within a finite shear zone, and the friction power, which is spent for overcoming the friction at the rake face. In calculating the shearing power, rate-sensitive plastic behavior of fcc metals is considered. In addition, realistic effects of lattice rotation and strain hardening are included in the model. Subsequently, the total power is minimized within the space of geometrically allowable shear angles to determine the shear angle solution, and associated cutting and thrust specific energies, as a function of cutting plane orientation, cutting direction (with respect to the crystal orientation), rake angle, and the coefficient of friction. The calibration procedure for and the experimental validation of the model are provided in Part II.
Skip Nav Destination
Article navigation
June 2011
Research Papers
A Rate-Sensitive Plasticity-Based Model for Machining of Face-Centered Cubic Single-Crystals—Part I: Model Development
Nithyanand Kota,
Nithyanand Kota
Department of Mechanical Engineering,
Carnegie Mellon University
, Pittsburgh
, PA 15213
Search for other works by this author on:
Anthony D. Rollett,
Anthony D. Rollett
Department of Materials Science and Engineering,
Carnegie Mellon University
, Pittsburgh
, PA 15213
Search for other works by this author on:
O. Burak Ozdoganlar
O. Burak Ozdoganlar
Department of Mechanical Engineering, Department of Materials Science and Engineering,
Carnegie Mellon University
, Pittsburgh
, PA 15213 e-mail:
Search for other works by this author on:
Nithyanand Kota
Department of Mechanical Engineering,
Carnegie Mellon University
, Pittsburgh
, PA 15213
Anthony D. Rollett
Department of Materials Science and Engineering,
Carnegie Mellon University
, Pittsburgh
, PA 15213
O. Burak Ozdoganlar
Department of Mechanical Engineering, Department of Materials Science and Engineering,
Carnegie Mellon University
, Pittsburgh
, PA 15213 e-mail: J. Manuf. Sci. Eng. Jun 2011, 133(3): 031017 (8 pages)
Published Online: July 1, 2011
Article history
Received:
March 17, 2010
Revised:
March 29, 2011
Online:
July 1, 2011
Published:
July 1, 2011
Citation
Kota, N., Rollett, A. D., and Ozdoganlar, O. B. (July 1, 2011). "A Rate-Sensitive Plasticity-Based Model for Machining of Face-Centered Cubic Single-Crystals—Part I: Model Development." ASME. J. Manuf. Sci. Eng. June 2011; 133(3): 031017. https://doi.org/10.1115/1.4004134
Download citation file:
Get Email Alerts
Cited By
Special Issue on the State-of-the-Art in Japanese Manufacturing Research
J. Manuf. Sci. Eng
A Review of Advanced Roll-to-Roll Manufacturing: System Modeling and Control
J. Manuf. Sci. Eng (April 2025)
Related Articles
A Slip-Based Model for Strength Evolution During Cyclic Loading
J. Eng. Mater. Technol (October,2004)
A Rate-Sensitive Plasticity-Based Model for Machining of fcc Single-Crystals—Part II: Model Calibration and Validation
J. Manuf. Sci. Eng (June,2011)
An Analytical Model for the Prediction of Minimum Chip Thickness in Micromachining
J. Manuf. Sci. Eng (May,2006)
Effects of Crystallographic Anistropy on Orthogonal Micromachining of Single-Crystal Aluminum
J. Manuf. Sci. Eng (June,2008)
Related Proceedings Papers
Related Chapters
Crack(s) in a Rod or a Plate by Energy Rate Analysis
The Stress Analysis of Cracks Handbook, Third Edition
Microstructure Evolution and Physics-Based Modeling
Ultrasonic Welding of Lithium-Ion Batteries
On-Line a Predictive Model of Cutting Force in Turning with 3 Axis Acceleration Transducer Using Neural Network
International Conference on Advanced Computer Theory and Engineering (ICACTE 2009)