For a range of precision machining and micromachining operations, the crystallographic anisotropy plays a critical role in determining the machining forces. Part II of this work presents the calibration and validation of the rate-sensitive plasticity-based machining (RSPM) model developed in Part I. The five material parameters, including four hardening parameters and the exponent of rate sensitivity, for both single-crystal aluminum and single-crystal copper are calibrated from the single-crystal plunge-turning data using a Kriging-based minimization approach. Subsequently, the RSPM model is validated by comparing the specific energies obtained from the model to those from a single-crystal cutting test. The RSPM model is seen to capture the experimentally observed variation of specific energies with crystallographic anisotropy (orientation), including the mean value, symmetry, specific trend, amplitude, and phase of the peak specific energy. The effects of lattice rotation, hardening, and material-parameter variations on the predicted specific energies is then analyzed, revealing the importance of both lattice rotation and hardening in accurately capturing the specific energies when cutting single-crystals. Using the RSPM model, the effects of crystallographic orientation, rake angle and friction angle on specific energies are also analyzed. Lastly, a simplified model that uses Merchant’s shear angle, thereby circumventing the minimization procedure, is constructed and evaluated.
Skip Nav Destination
Article navigation
June 2011
Research Papers
A Rate-Sensitive Plasticity-Based Model for Machining of fcc Single-Crystals—Part II: Model Calibration and Validation
Nithyanand Kota,
Nithyanand Kota
Department of Mechanical Engineering,
Carnegie Mellon University
, Pittsburgh
, PA 15213
Search for other works by this author on:
Anthony D. Rollett,
Anthony D. Rollett
Department of Materials Science and Engineering,
Carnegie Mellon University
, Pittsburgh
, PA 15213
Search for other works by this author on:
O. Burak Ozdoganlar
O. Burak Ozdoganlar
Department of Mechanical Engineering
, Department of Materials Science and Engineering, Carnegie Mellon University
, Pittsburgh
, PA 15213; e-mail:
Search for other works by this author on:
Nithyanand Kota
Department of Mechanical Engineering,
Carnegie Mellon University
, Pittsburgh
, PA 15213
Anthony D. Rollett
Department of Materials Science and Engineering,
Carnegie Mellon University
, Pittsburgh
, PA 15213
O. Burak Ozdoganlar
Department of Mechanical Engineering
, Department of Materials Science and Engineering, Carnegie Mellon University
, Pittsburgh
, PA 15213; e-mail: J. Manuf. Sci. Eng. Jun 2011, 133(3): 031018 (9 pages)
Published Online: July 1, 2011
Article history
Received:
March 17, 2010
Revised:
March 29, 2011
Online:
July 1, 2011
Published:
July 1, 2011
Citation
Kota, N., Rollett, A. D., and Ozdoganlar, O. B. (July 1, 2011). "A Rate-Sensitive Plasticity-Based Model for Machining of fcc Single-Crystals—Part II: Model Calibration and Validation." ASME. J. Manuf. Sci. Eng. June 2011; 133(3): 031018. https://doi.org/10.1115/1.4004135
Download citation file:
Get Email Alerts
Cited By
Related Articles
A Rate-Sensitive Plasticity-Based Model for Machining of Face-Centered Cubic Single-Crystals—Part I: Model Development
J. Manuf. Sci. Eng (June,2011)
Effects of Crystallographic Anistropy on Orthogonal Micromachining of Single-Crystal Aluminum
J. Manuf. Sci. Eng (June,2008)
Dynamic Material Behavior Modeling Using Internal State Variable Plasticity and Its Application in Hard Machining Simulations
J. Manuf. Sci. Eng (August,2006)
Decomposition of Thermal and Mechanical Effects on Microstructure and Hardness of Hard Turned Surfaces
J. Manuf. Sci. Eng (May,2004)
Related Chapters
GA Based Multi Objective Optimization of the Predicted Models of Cutting Temperature, Chip Reduction Co-Efficient and Surface Roughness in Turning AISI 4320 Steel by Uncoated Carbide Insert under HPC Condition
Proceedings of the 2010 International Conference on Mechanical, Industrial, and Manufacturing Technologies (MIMT 2010)
On-Line a Predictive Model of Cutting Force in Turning with 3 Axis Acceleration Transducer Using Neural Network
International Conference on Advanced Computer Theory and Engineering (ICACTE 2009)
Mechanics of Crack Tip Deformation and Extension by Fatigue
Fatigue Crack Propagation