Finite element modeling (FEM) of machining-induced residual stresses (RS) takes place over two consecutive steps: a cutting step and a relaxation step. In the latter, the workpiece is left to cool down after deactivating all external loads. The current work focuses on the relaxation step, and how different strain components, material plasticity, and workpiece edge deflections affect the final state of different RS components. First, a two-dimensional arbitrary-Lagrangian–Eulerian (ALE) plane strain thermomechanical explicit model was used to simulate dry orthogonal cutting. After that, the relaxation process was modeled using three approaches: (1) the classical approach, (2) a new approach that is first presented here, and (3) a modified approach that was developed earlier by the current author. In the classical approach, the same exact machined workpiece is relaxed, considering all stress/strain components and material plasticity. On the other hand, the new approach uses a pure elastic one-dimensional thermal relaxation model, in the cutting direction, and assumes that the workpiece edges normal to the cutting direction remain so. The differences between the RS predicted by the new and classical approaches reflected the combined effects of the examined parameters. The role of each parameter was isolated using three different versions of the modified approach. The current findings confirmed that for orthogonal cutting, the stress relaxation process can be considered as a one-dimensional pure elastic thermal relaxation process. Also, the workpiece edges normal to the cutting direction deflect during relaxation, contributing to the final state of RS.
Skip Nav Destination
Article navigation
July 2017
Research-Article
On the Role of Different Strain Components, Material Plasticity, and Edge Effects When Predicting Machining-Induced Residual Stresses Using Finite Element Modeling
Mohamed N. A. Nasr
Mohamed N. A. Nasr
Department of Mechanical Engineering,
Faculty of Engineering,
Alexandria University,
Alexandria 21544, Egypt
e-mail: m.nasr@alexu.edu.eg
Faculty of Engineering,
Alexandria University,
Alexandria 21544, Egypt
e-mail: m.nasr@alexu.edu.eg
Search for other works by this author on:
Mohamed N. A. Nasr
Department of Mechanical Engineering,
Faculty of Engineering,
Alexandria University,
Alexandria 21544, Egypt
e-mail: m.nasr@alexu.edu.eg
Faculty of Engineering,
Alexandria University,
Alexandria 21544, Egypt
e-mail: m.nasr@alexu.edu.eg
Manuscript received July 17, 2016; final manuscript received February 14, 2017; published online April 12, 2017. Assoc. Editor: Radu Pavel.
J. Manuf. Sci. Eng. Jul 2017, 139(7): 071014 (8 pages)
Published Online: April 12, 2017
Article history
Received:
July 17, 2016
Revised:
February 14, 2017
Citation
Nasr, M. N. A. (April 12, 2017). "On the Role of Different Strain Components, Material Plasticity, and Edge Effects When Predicting Machining-Induced Residual Stresses Using Finite Element Modeling." ASME. J. Manuf. Sci. Eng. July 2017; 139(7): 071014. https://doi.org/10.1115/1.4036122
Download citation file:
Get Email Alerts
Cited By
On-Orbit Processing and Hardware Performance of Microgravity Hydrothermal Synthesis for Graphene Aerogel
J. Manuf. Sci. Eng (December 2024)
A Review on Metallic Drilling Burrs: Geometry, Formation, and Effect on the Mechanical Strength of Metallic Assemblies
J. Manuf. Sci. Eng (April 2025)
Related Articles
Enhanced Surface Integrity From Cryogenic Machining of AZ31B Mg
Alloy: A Physics-Based Analysis With Microstructure Prediction
J. Manuf. Sci. Eng (June,2017)
Dynamic Material Behavior Modeling Using Internal State Variable Plasticity and Its Application in Hard Machining Simulations
J. Manuf. Sci. Eng (August,2006)
The Influence of Material Models on Finite Element Simulation of Machining
J. Manuf. Sci. Eng (November,2004)
Finite Element Modeling of Edge Trimming Fiber Reinforced Plastics
J. Manuf. Sci. Eng (February,2002)
Related Chapters
Microstructure Evolution and Physics-Based Modeling
Ultrasonic Welding of Lithium-Ion Batteries
Modeling of Cutting Force in Vibration-Assisted Machining
Vibration Assisted Machining: Theory, Modelling and Applications
Finite Element Modeling and Analysis of Vibration-Assisted Machining
Vibration Assisted Machining: Theory, Modelling and Applications