1-15 of 15
Keywords: simulation
Close
Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Journal Articles
Article Type: Research Papers
J. Manuf. Sci. Eng. December 2021, 143(12): 121005.
Paper No: MANU-21-1077
Published Online: June 22, 2021
..., the authors present a finite element simulation technique to evaluate the opening stress levels for two structural steels (25CrMo4 and 30NiCrMoV12) under low-cycle fatigue conditions. The LCF experimental results were used to obtain kinematic hardening parameters through the Chaboche model. The finite element...
Journal Articles
Article Type: Research Papers
J. Manuf. Sci. Eng. February 2021, 143(2): 021008.
Paper No: MANU-20-1225
Published Online: October 8, 2020
...Pradeep Kumar Krishnan; Ramanathan Arunachalam; Afzal Husain; Majid Al-Maharbi In the present work, the influence of stirrer blade design on the dispersion of reinforcement particles in the aluminum metal matrix was studied extensively through experiments and also simulated them using...
Journal Articles
Article Type: Review Articles
J. Manuf. Sci. Eng. November 2020, 142(11): 110816.
Paper No: MANU-20-1083
Published Online: September 29, 2020
... automation modeling simulation sensing monitoring diagnostics sensors joining Manufacturing is the production of products for use or sale using labor and machines, tools, chemical or biological processing or formulation and is the essence of secondary industry. The term may refer to a range...
Journal Articles
Article Type: Research Papers
J. Manuf. Sci. Eng. April 2020, 142(4): 041004.
Paper No: MANU-19-1337
Published Online: February 28, 2020
... and the side gap did not vanish immediately when a breakout happened and could still evacuate debris for a short period. The debris gradually accumulated as the fluid flow in the gap vanished. A series of simulations were conducted to study the fluid flow and debris movement after the breakout. And simulations...
Journal Articles
Article Type: Research Papers
J. Manuf. Sci. Eng. December 2019, 141(12): 121002.
Paper No: MANU-19-1048
Published Online: October 17, 2019
... and spatial coordinates for the points that define the cutting edges that are extracted. These points are then used to determine the cutting edge radius and angle at equally spaced points along the tool's axis. This cutting edge geometry is applied directly in a time domain simulation that predicts...
Journal Articles
Article Type: Research-Article
J. Manuf. Sci. Eng. December 2016, 138(12): 121015.
Paper No: MANU-16-1055
Published Online: September 29, 2016
... finite-element analysis using forge ® software in terms of teeth forming and forming loads evolution. Based on these simulations, the experimental investigations were carried out to obtain a spur gear form with the good quality, using several billet dimensions. The experimental trials and simulations...
Journal Articles
Article Type: Research-Article
J. Manuf. Sci. Eng. October 2014, 136(5): 051021.
Paper No: MANU-14-1138
Published Online: August 12, 2014
...Masato Ikegawa; Eiji Ishii; Nobuhiro Harada; Tsuneaki Takagishi Here the effect of Coulomb's forces on the trajectories was examined. As the experiment without Coulomb's forces cannot be performed, only simulation without Coulomb's forces was performed. The results labeled Sim (Leading...
Journal Articles
Article Type: Research Papers
J. Manuf. Sci. Eng. December 2010, 132(6): 061001.
Published Online: October 15, 2010
... nonthermal process makes it possible to form without material degradation or even improve them by inducing compressive stress over the target surface. In the present study, a fully three-dimensional numerical model is developed to simulate the forming process of laser peen forming. The simulation procedure...
Journal Articles
Article Type: Research Papers
J. Manuf. Sci. Eng. February 2010, 132(1): 011014.
Published Online: February 2, 2010
...D. Barrenetxea; J. Álvarez; J. I. Marquínez; J. Madariaga; I. Gallego; I. Muguerza Perelló This paper presents new simulation models and global stability charts that have been developed to analyze the principal instabilities and constraints involved in the throughfeed centerless grinding process...
Journal Articles
Article Type: Research Papers
J. Manuf. Sci. Eng. February 2010, 132(1): 011016.
Published Online: February 2, 2010
.... A simple analysis of the mechanics of this thinning phenomenon is presented. Finite element simulation results are presented for different sheet-die friction conditions. Sheet thickness profiles measured from parts produced in forming experiments using three different lubrication conditions are compared...
Journal Articles
Article Type: Technical Papers
J. Manuf. Sci. Eng. June 2007, 129(3): 661–668.
Published Online: February 7, 2007
... for short time periods. This research developed a systematic method on when to shut down equipment to do maintenance in an automotive assembly environment. It is called maintenance opportunity. The method incorporated real-time information about production and machine failure conditions. A simulation-based...
Journal Articles
Article Type: Research Papers
J. Manuf. Sci. Eng. October 2007, 129(5): 911–918.
Published Online: November 3, 2006
...Dimitriou Vasilis; Vidakis Nectarios; Antoniadis Aristomenis Gear hobbing, as any cutting process based on the rolling principle, is a signally multiparametric and complicated gear fabrication method. Although a variety of simulating methods has been proposed, each of them somehow reduces...
Journal Articles
Article Type: Technical Papers
J. Manuf. Sci. Eng. August 2005, 127(3): 677–686.
Published Online: August 1, 2004
... system is modeled, simulated, and implemented. The particleboard model is based on the characterization of surface anomalies (pinholes, sander streaks, and grooves). Furthermore, an optical stylus surface-roughness measurement system is also modeled in order to determine whether it can be used...
Journal Articles
Article Type: Technical Papers
J. Manuf. Sci. Eng. May 2003, 125(2): 236–244.
Published Online: April 15, 2003
...Hanxin Zhao; Kornel F. Ehmann In this part of the paper the analytical models for the prediction of the force system, established in Part 1, in conjunction with a complete geometric model of the spade bit, will be used in a systematic simulation analysis of the spade drill’s performance. The aim...
Journal Articles
Article Type: Technical Papers
J. Manuf. Sci. Eng. May 2003, 125(2): 304–309.
Published Online: April 15, 2003
... and simulation results have been verified by experimental trials. It was found that even a little slip ± 1.5 ° ∼ 3 ° between the workpiece and driverhead can yield a better result. However, to thoroughly understand the performance of shoe centerless grinding, more studies are needed in the near...