The constitutive properties of hard alpha Ti were recently generated by Chan et al., 2000, “Constitutive Properties of Hard Alpha Titanium,” Metall. and Maters. Trans. A, Vol. 31A, pp. 3029–3040, using uniaxial compression, indirect tension, indentation, and plane strain compression tests. Flow stress and fracture strength of hard alpha were measured as a function of stress state, strain rate, temperature, and nitrogen content. Hard alpha exhibited plastic flow at low nitrogen contents (<4 wt. percent N), but elastic fracture at high nitrogen contents (>6 wt. percent N). In this paper, this set of constitutive data is used to develop constitutive equations for describing the inelastic deformation and damage accumulation behavior of hard alpha Ti.
Skip Nav Destination
Article navigation
July 2001
Technical Papers
Constitutive Relations for Inelastic Deformation and Damage Accumulation in Hard Alpha Titanium
Kwai S. Chan, Mem. ASME
Kwai S. Chan, Mem. ASME
Southwest Research Institute, 6220 Culebra Road, San Antonio, TX 78238
Search for other works by this author on:
Kwai S. Chan, Mem. ASME
Southwest Research Institute, 6220 Culebra Road, San Antonio, TX 78238
Contributed by the Materials Division for publication in the JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY. Manuscript received by the Materials Division May 25, 2000; revised manuscript received March 11, 2001. Associate Editor: D. Marquis.
J. Eng. Mater. Technol. Jul 2001, 123(3): 281-286 (6 pages)
Published Online: March 11, 2001
Article history
Received:
May 25, 2000
Revised:
March 11, 2001
Citation
Chan, K. S. (March 11, 2001). "Constitutive Relations for Inelastic Deformation and Damage Accumulation in Hard Alpha Titanium ." ASME. J. Eng. Mater. Technol. July 2001; 123(3): 281–286. https://doi.org/10.1115/1.1373653
Download citation file:
Get Email Alerts
Cited By
High-Temperature Thermal Transport Properties of Multifunctional PTFE/PEEK-Matrix Composite With Short Carbon Fibers and Graphite Flakes
J. Eng. Mater. Technol (October 2022)
Closed-Form General Relationship Model for the Interfacial Oxidation of Cylindrically Curved Surfaces
J. Eng. Mater. Technol (July 2022)
Experimental Study on Laser-Induced Surface Damage of a Single-Crystal Nickel-Based Superalloy Under Continuous Wave Fiber Laser Scanning Process
J. Eng. Mater. Technol (October 2022)
Extension of the Adjustable Localization Operator Method to Anisotropic Elasto-Plastic Behavior for Low-Cycle Fatigue Life Prediction
J. Eng. Mater. Technol (October 2022)
Related Articles
Effect of dc on the Formability of Ti–6Al–4V
J. Eng. Mater. Technol (July,2009)
Compressive Kinking of Fiber Composites: A Topical Review
Appl. Mech. Rev (June,1994)
Prediction of Ductile-to-Brittle Transition Under Different Strain Rates in Undermatched Welded Joints
J. Pressure Vessel Technol (June,2011)
Interfacial Fracture Toughness Measurement of a Ti/Si Interface
J. Electron. Packag (September,2004)
Related Proceedings Papers
Related Chapters
Introduction and Definitions
Handbook on Stiffness & Damping in Mechanical Design
Understanding the Problem
Design and Application of the Worm Gear
Forging Strain Rate and Deformation Temperature Effects on the Fracture Toughness Properties of Type 304L Stainless Steel Precharged with Tritium
International Hydrogen Conference (IHC 2016): Materials Performance in Hydrogen Environments