Standard procedures available for evaluating gear fillet stresses are targeted to circular gears where little information is available about noncircular gears. In this paper, a mesh generation algorithm is presented for the discretization of gear tooth profiles of noncircular gear elements for static stress evaluation using FEM (Finite Element Method). The procedure assumes that the noncircular gear tooth profile is known. Delimiting a tooth domain from the gear structure and subdividing it into sectors, the gear tooth mesh is generated by mapping pregenerated patterns into the sectors. The discretized tooth domain is used in conjunction with the FEM to obtain stresses within the tooth fillet region. For comparison, this procedure was applied to determine the stress distribution in circular gears and rectangular beams. The results were in complete agreement with existing analytical solutions. An illustrating example is presented where a noncircular gear pair is introduced to eliminate the speed and torque fluctuation that exists in an electrical generator when an I.C. engine is used as the power source for the generator. The maximum fillet Von Mises stress is calculated for each angular position of the noncircular gear pair.

Issue Section:
Technical Papers
Keywords:
rotating bodies, torque, finite element analysis, stress analysis, elasticity, mesh generation
Topics:
Gears, Mesh generation, Stress, Torque, Gear teeth, Finite element methods
1.
Wilcox
,
L.
, and
Coleman
,
W.
,
1973
, “
Application of Finite Elements to the Analysis of Gear Tooth Stresses
,”
ASME J. Eng. Ind.
,
95
, pp.
1139
–
1148
.
2.
Chabert
,
G.
,
Dang Tran
,
T.
, and
Mathis
,
R.
,
1974
, “
An Evaluation of Stresses and Deflection of Spur Gear Teeth Under Strain
,”
ASME J. Eng. Ind.
,
96
, pp.
85
–
93
.
3.
Tobe
,
T.
,
Kato
,
M.
, and
Inoue
,
K.
,
1978
, “
Bending of Stub Cantilever Plate and Some Applications to Strength of Gear Teeth
,”
ASME J. Mech. Des.
,
100
, pp.
374
–
381
.
4.
Wellauer
,
E. J.
, and
Seireg
,
A.
,
1960
, “
Bending Strength of Gear Teeth by Cantilever-Plate Theory
,”
ASME J. Eng. Ind.
,
82
, pp.
213
–
222
.
5.
Andrews
,
J. D.
,
1991
, “
A Finite Element Analysis of Bending Stresses Induced in External and Internal Involute Spur Gears
,”
J. Strain Anal.
,
26
(
3
), pp.
154
–
163
.
6.
Reinhart
,
W. R.
,
Ferguson
,
R. J.
, and
Kerr
,
J. H.
,
1980
, “
Noncircular Gear Tooth Bending Strength by Finite Element Analysis
,”
Trans. Can. Soc. Mech. Eng.
,
6
(
2
), pp.
71
–
77
.
7.
Huseyin
,
I. F.
, and
Eyercioglu
,
O.
,
1995
, “
Evaluation of Gear Tooth Stresses by Finite Element Method
,”
ASME J. Eng. Ind.
,
117
, pp.
232
–
239
.
8.
Sandeep, M. V., Biplab, S., and Houser, R. D., 1987, “Gear Tooth Profile Determination from Arbitrary Rack Geometry,” AGMA Technical Paper, AGMA 1987, 13pp.
9.
Gengdong
,
C.
, and
Hua
,
L.
,
1996
, “
New Method for Graded Mesh Generation of Quadrilateral Finite Elements
,”
Computers and Structures
,
59
(
5
),
823
–
829
.
10.
Cook
,
W. A.
,
1974
, “
Body Oriented (Natural) Coordinates for Generating Three Dimensional Meshes
,”
International Journal for Numerical Methods in Engineering
,
8
, pp.
27
–
43
.
11.
Herrmann
,
L. R.
,
1976
, “
Laplacian-Isoparametric Grid Generation Scheme
,”
J. Eng. Mech. Div., Am. Soc. Civ. Eng.
,
102
, pp.
749
–
756
.
12.
Shigley, J. E., and Mischke, C. R., 1996, Standard Handbook of Machine Design, Second Edition, McGraw Hill Companies.
13.
Dooner
,
D. B.
,
1997
, “
Use of Non-Circular Gears to Reduce Torque and Speed Fluctuations in Rotating Shafts
,”
ASME J. Mech. Des.
,
119
, pp.
299
–
306
.
14.
Dooner, D. B., and Seireg, A., 1995, The Kinematic Geometry of Gearing, John Wiley and Sons, Inc., New York.
Copyright © 2002
 by ASME
You do not currently have access to this content.