Abstract

The fuzzy front end of engineering design can present a difficult challenge, and as such, recent engineering design research has focused on guiding and influencing the way a designer ideates. Early ideation can be especially difficult when attempting to integrate specific design objectives in product design, called Design for X (DfX). This paper presents two experiments exploring the efficacy of a structured Design for the Environment (DfE) design method called the Guidelines and Regulations for Early design for the Environment (GREEn) Quiz that provides designers with sustainable design knowledge during the conceptual design phase. The GREEn Quiz operates on a web-based platform and queries the designer about their design concepts; an end-of-quiz report provides abstract DfE knowledge to designers. While this abstract knowledge was able to be applied by designers in a former study, we hypothesize that providing targeted, specific design strategies during conceptual design will enable novice designers to better integrate DfE. In this study, we created these DfE strategies, integrated these into the GREEn Quiz, and studied the efficacy of these strategies when presented to designers at both the expert and novice levels. Results suggest that respondents with access to the strategy-based GREEn Quiz produced concepts with evidence of a broader range of sustainable design decisions and higher solution quality scores. This work shows the promise of supplemental DfE methods for concept generation to enable the design of more environmentally sustainable products.

References

1.
Alberts
,
B.
,
Cicerone
,
R.
,
Academy
,
N.
,
Board
,
P. E.
,
Science
,
S.
, and
Biology
,
C.
,
2007
, “
Sustainability Science: A Room of Its Own
,”
PNAS
,
104
(
6
), pp.
1737
1738
.
2.
Birch
,
A.
,
Hon
,
K. K. B.
, and
Short
,
T.
,
2012
, “
Structure and Output Mechanisms in Design for Environment (DfE) Tools
,”
J. Clean. Prod.
,
35
, pp.
50
58
.
3.
Sihvonen
,
S.
, and
Partanen
,
J.
,
2017
, “
Eco-Design Practices With a Focus on Quantitative Environmental Targets: An Exploratory Content Analysis Within ICT Sector
,”
J. Clean. Prod.
,
143
, pp.
769
783
.
4.
Otto
,
K.
, and
Wood
,
K.
,
2001
,
Product Design: Techniques in Reverse Engineering and New Product Development
,
Prentice Hall
,
New York
.
5.
Ullman
,
D. G.
,
2010
,
The Mechanical Design Process
, 4th ed.,
McGraw-Hill
,
New York
.
6.
Bovea
,
M. D.
, and
Pérez-Belis
,
V.
,
2012
, “
A Taxonomy of Ecodesign Tools for Integrating Environmental Requirements Into the Product Design Process
,”
J. Clean. Prod.
,
20
(
1
), pp.
61
71
.
7.
Rossi
,
M.
,
Germani
,
M.
, and
Zamagni
,
A.
,
2016
, “
Review of Ecodesign Methods and Tools. Barriers and Strategies for an Effective Implementation in Industrial Companies
,”
J. Clean. Prod.
,
129
, pp.
361
373
.
8.
Ramani
,
K.
,
Ramanujan
,
D.
,
Bernstein
,
W. Z.
,
Zhao
,
F.
,
Sutherland
,
J.
,
Handwerker
,
C.
,
Choi
,
J.-K.
,
Kim
,
H.
, and
Thurston
,
D.
,
2010
, “
Integrated Sustainable Life Cycle Design: A Review
,”
ASME J. Mech. Des.
,
132
(
9
), p.
091004
.
9.
The International Standards Organisation
,
2006
. “
Environmental Management—Life Cycle Assessment—Principles and Framework
,” ISO 14040, 2006, p.
1
28
.
10.
Tensa
,
M.
,
Ferrero
,
V.
,
Ross
,
D.
, and
DuPont
,
B.
,
2018
, “
Assessing the Impact of Product Use Variation on Environmental Sustainability
,”
ASME International Design Engineering Technical Conferences & Computers and Information in Engineering Conference
,
Quebec City, QC, Canada
,
Aug. 26–29
, pp.
1
9
.
11.
Wisthoff
,
A.
,
Ferrero
,
V.
,
Huynh
,
T.
, and
DuPont
,
B. L.
,
2016
, “
Quantifying the Impact of Sustainable Product Design Decisions in the Early Design Phase Through Machine Learning
,”
ASME 2016 International Design Engineering Technical Conference & Computers and Information in Engineering Conference
,
Charlotte, NC
,
August
, pp.
1
10
.
12.
Eastman
,
C. M.
,
1996
,
Design for X: Concurrent Engineering Imperatives
, 1st ed.,
Springer Science & Business Media
.
13.
“Geometric DFX by DFMPro,” https://dfmpro.com/cad-systems/dfx/, Accessed May 2018.
14.
“Environmental Management Systems—Guidelines for Incorporating Ecodesign Systèmes,”
2011
.
15.
US Congress
,
1969
, “
National Environmental Policy Act of 1969, as Amended
,”
Environmental History
,
5
(
4
).
16.
Pigosso
,
D.
, and
McAloone
,
T.
,
2017
, “
How Can Design Science Contribute to a Circular Economy?
International Conference on Engineering Design
,
Vancouver, BC, Canada
,
August
, pp.
299
307
.
17.
Klöpffer
,
W.
,
1997
, “
Life Cycle Assessment: From the Beginning to the Current State
,”
Environ. Sci. Pollut. Res. Int.
,
4
(
4
), pp.
223
228
.
18.
Marosky
,
N.
,
Dose
,
J.
,
Fleischer
,
G.
, and
Ackermann
,
R.
,
2007
, “
Challenges of Data Transfer Between CAD and LCA Software Tools
,”
Proceedings of the 3rd International Conference on Life Cycle Management
,
Zurich
,
Aug. 27–29
.
19.
Gaha
,
R.
,
Benamara
,
A.
, and
Yannou
,
B.
,
2013
, “A Feature-Based Methodology for Eco-Designing Parts on Detail Phase,”
Lect. Notes Mech. Eng.
, Vol.
1
,
Springer Link
, pp.
645
654
.
20.
SolidWorks
, “
SolidWorks Sustainability
.”
21.
Luttropp
,
C.
, and
Lagerstedt
,
J.
,
2006
, “
EcoDesign and The Ten Golden Rules: Generic Advice for Merging Environmental Aspects Into Product Development
,”
J. Clean. Prod.
,
14
(
15–16
), pp.
1396
1408
.
22.
Brambila
,
S.
, and
Sakao
,
T.
,
2018
,
Designing Sustainable Technologies, Products and Policies
,
SpringerLink
,
New York City
.
23.
Telenko
,
C.
,
O’Rourke
,
J. M.
,
Conner Seepersad
,
C.
, and
Webber
,
M. E.
,
2016
, “
A Compilation of Design for Environment Guidelines
,”
ASME J. Mech. Des.
,
138
(
3
), p.
031102
.
24.
Bovea
,
M. D.
, and
Pérez-Belis
,
V.
,
2018
, “
Identifying Design Guidelines to Meet the Circular Economy Principles: A Case Study on Electric and Electronic Equipment
,”
J. Environ. Manage.
,
228
, pp.
483
494
.
25.
Saidani
,
M.
,
Kim
,
H.
,
Cluzel
,
F.
,
Leroy
,
Y.
, and
Yannou
,
B.
,
2020
, “
Product Circularity Indicators: What Contributions in Designing for a Circular Economy?
Proceedings of the Design Society: DESIGN Conference
,
Virtual
,
Oct. 26–29
.
26.
Saidani
,
M.
,
Yannou
,
B.
,
Leroy
,
Y.
, and
Cluzel
,
F.
,
2017
, “
Hybrid Top-Down and Bottom-Up Framework to Measure Products’ Circularity Performance
,”
Proc. Int. Conf. Eng. Des. ICED
,
1
(
DS87-1
), pp.
81
90
.
27.
Telenko
,
C.
,
2009
, “
Developing Green Design Guidelines: A Formal Method and Case Study
,” Masters Thesis in Mechanical Engineering,
Georgia Tech
,
Atlanta, GA
.
28.
Le Pochat
,
S.
,
Bertoluci
,
G.
, and
Froelich
,
D.
,
2007
, “
Integrating Ecodesign by Conducting Changes in SMEs
,”
J. Clean. Prod.
,
15
(
7
), pp.
671
680
.
29.
Kobayashi
,
H.
,
2006
, “
A Systematic Approach to Eco-Innovative Product Design Based on Life Cycle Planning
,”
Adv. Eng. Inf.
,
20
(
2
), pp.
113
125
.
30.
Tingström
,
J.
, and
Karlsson
,
R.
,
2006
, “
The Relationship Between Environmental Analyses and the Dialogue Process in Product Development
,”
J. Clean. Prod.
,
14
(
15–16
), pp.
1409
1419
.
31.
Cappelli
,
F.
,
Delogu
,
M.
, and
Pierini
,
M.
,
2006
, “
Integration of LCA and EcoDesign Guideline in a Virtual CAD Framework
,”
CIRP: The International Academy for Production Engineering: International Conference on Life Cycle Engineering
,
Leuven, Belgium
,
May 31–June 2
, pp.
185
188
.
32.
National Academy of Engineering
,
2005
,
Educating the Engineer of 2020
,
The National Academies Press
,
Washington, DC
.
33.
Smith
,
G.
,
Richardson
,
J.
,
Summers
,
J. D.
, and
Mocko
,
G. M.
,
2012
, “
Concept Exploration Through Morphological Charts: An Experimental Study
,”
ASME J. Mech. Des.
,
134
(
5
), p.
051004
.
34.
Tayal
,
S. P.
,
2013
, “
Engineering Design Process
,”
Int. J. Comput. Sci. Commun. Eng. IJCSCE Spec. Issue, Recent Adv. Eng. Technol.
, pp.
1
5
.
35.
Devanathan
,
S.
,
Ramanujan
,
D.
,
Bernstein
,
W. Z.
,
Zhao
,
F.
, and
Ramani
,
K.
,
2010
, “
Integration of Sustainability Into Early Design Through the Function Impact Matrix
,”
ASME J. Mech. Des.
,
132
(
8
), p.
081004
.
36.
McAdams
,
D. A.
, and
Wood
,
K. L.
,
2002
, “
A Quantitative Similarity Metric for Design-by-Analogy
,”
ASME J. Mech. Des.
,
124
(
2
), pp.
173
182
.
37.
Srinivasan
,
V.
,
Song
,
B.
,
Luo
,
J.
,
Subburaj
,
K.
,
Elara
,
M. R.
, and
Wood
,
K.
,
2017
, “
Investigating Effects of Stimuli on Ideation Outcomes
,”
Proceedings of the 21st International Conference on Engineering Design (ICED)
,
Vancouver, BC, Canada
,
Aug. 21–25
.
38.
Fu
,
K.
,
Chan
,
J.
,
Cagan
,
J.
,
Kotovsky
,
K.
,
Schunn
,
C.
, and
Wood
,
K.
,
2018
, “
The Meaning of ‘ Near ‘ and ‘ Far ‘: The Impact of Structuring Design Databases and the Effect of Distance of Analogy on Design Output
,”
ASME J. Mech. Des.
,
135
(
2
), pp.
1
12
.
39.
Chen
,
J. L.
, and
Liu
,
C.
,
2001
, “
An Eco-Innovative Design Approach Incorporating the TRIZ Method Without Contradiction Analysis
,”
J. Sustain. Prod. Des.
,
1
, pp.
263
272
.
40.
Talabǎ
,
D.
, and
Roche
,
T.
,
2005
,
Product Engineering: Eco-Design, Technologies and Green Energy, Springer, Netherlands.
41.
Linsey
,
J.
,
Tseng
,
I.
,
Fu
,
K.
,
Cagan
,
J.
, and
Wood
,
K. L.
,
2009
, “
Reducing and Perceiving Design Fixation: Initial Results From an NSF-Sponsored Workshop
,”
DS 58-9: Proceedings of ICED 09, the 17th International Conference on Engineering Design
,
Palo Alto, CA
,
Aug. 24–27
, Vol. 9, pp.
233
244
.
42.
Crilly
,
N.
,
2015
, “
Fixation and Creativity in Concept Development: The Attitudes and Practices of Expert Designers
,”
Des. Stud.
,
38
, pp.
54
91
.
43.
DuPont
,
B.
, and
Wisthoff
,
A.
,
2015
, “
An Innovation-Based Method for the Design of Sustainable Products
,”
International Congress on Sustainability Science and Engineering
,
Balatonfured, Hungary
,
Apr. 5–8
.
44.
Wisthoff
,
A.
,
Ferrero
,
V.
,
Huynh
,
T.
, and
DuPont
,
B.
,
2016
, “
Quantifying the Impact of Sustainable Product Design Decisions in the Early Design Phase Through Machine Learning
,”
International Design Engineering Technical Conferences and Computers and Information in Engineering Conference
,
Charlotte, NC
,
August
, Vol. 50145, p. V004T05A043, American Society of Mechanical Engineers.
45.
Setchi
,
R.
,
Howlett
,
R. J.
,
Liu
,
Y.
, and
Theobald
,
P.
,
2016
, “
Sustainable Design and Manufacturing 2016
,”
Smart Innov. Syst. Technol.
,
52
, pp.
271
280
.
46.
Jansson
,
D. G.
, and
Smith
,
S. M.
,
1991
, “
Design Fixation
,”
Des. Stud.
,
12
(
1
), pp.
3
11
.
You do not currently have access to this content.