1-12 of 12
Keywords: lubrication
Close
Sort by
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Mech. Des. January 2012, 134(1): 011007.
Published Online: January 4, 2012
..., non-smooth paths. Such paths can be traced by rigid-body or partially compliant mechanisms as well but the complexity, bulkiness and the presence of hinges is a disadvantage in terms of increased friction, backlash, need for lubrication, noise, and vibrations. In designing CCMs, both curved frame...
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Mech. Des. January 2009, 131(1): 011003.
Published Online: December 11, 2008
.... The duration time to complete the squeeze process compared with the running time the pin takes to cover the entire arc of contact is fundamental to understand whether direct asperity-asperity contact occurs between the two approaching surfaces to clarify what actually is the lubrication regime...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Mech. Des. June 2008, 130(6): 062601.
Published Online: April 14, 2008
...-lubrication environment with three different gear lubricants. These tests were used to quantify the influence of these parameters on both load-dependent (mechanical), load-independent (spin), and total power loss. Trends in mechanical gear mesh efficiency and total gearbox efficiency were discussed in terms...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Mech. Des. January 2007, 129(1): 58–68.
Published Online: June 14, 2006
... to predict the instantaneous mechanical efficiency of a gear pair under typical operating, surface, and lubrication conditions. The friction model uses a new friction coefficient formula obtained by using a validated non-Newtonian thermal elastohydrodynamic lubrication (EHL) model in conjunction...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Mech. Des. September 2006, 128(5): 1165–1176.
Published Online: October 3, 2005
... and kinematics of leading examples are reviewed, including the factors affecting design optimization. Properties of the traction contacts are considered in detail, with particular attention to elastohydrodynamic lubrication and asperity contact. Factors affecting the traction coefficient are reviewed...
Journal Articles
Publisher: ASME
Article Type: Technical Papers
J. Mech. Des. September 2004, 126(5): 903–908.
Published Online: October 28, 2004
...Y. Diab; F. Ville; P. Velex; C. Changenet Power losses in high-speed gears come from the friction between the teeth (sliding and rolling), the lubrication process (dip or jet lubrication), the pumping of a gas-lubricant mixture during the meshing and the losses associated with windage effects...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Mech. Des. November 2005, 127(6): 1184–1190.
Published Online: October 26, 2004
... . Haraldsson , A. , Han , C.-S. , Tschöpe , H. , and Wriggers , P. , 1997 , “ Shape Optimization of a Lubricated Journal Bearing With Regard to the Distribution of Pressure in the Fluid ,” Eng. Optimiz. 0305-215X , 29 , pp. 259 – 275 . Kotera , H. , and Shima , S. , 2000...
Journal Articles
Publisher: ASME
Article Type: Technical Papers
J. Mech. Des. December 2002, 124(4): 805–812.
Published Online: November 26, 2002
... by friction coefficients for example, lubrication and operating conditions as well as the surroundings, the temperature rise of a rolling-sliding surface is so complicated a phenomenon that the surface temperature is thought to be impossible to calculate theoretically 28 . A method to predict the surface...
Journal Articles
Publisher: ASME
Article Type: Technical Papers
J. Mech. Des. March 2002, 124(1): 86–90.
Published Online: February 1, 2000
..., the mathematical model of an ideal valve gear was used. In addition, the comparison of the results between the polysine cam and the new MULTICAM cam design was made. By means of the new cam design the Hertz pressures were reduced at the point of contact between the cam and the cam follower and the lubrication...
Journal Articles
Publisher: ASME
Article Type: Technical Papers
J. Mech. Des. December 2000, 122(4): 484–488.
Published Online: October 1, 1999
...P. Ravn; S. Shivaswamy; B. J. Alshaer; Hamid M. Lankarani Proper modeling of joint clearance is of great importance in the analysis and design of multibody mechanical systems. The clearance may be due to wear or imperfection in manufacturing. When there is no lubricant in the clearance, solid...
Journal Articles
Publisher: ASME
Article Type: Technical Papers
J. Mech. Des. December 2001, 123(4): 598–605.
Published Online: June 1, 1999
.... An analytical study of frictional energy loss mechanisms for chain drives is given along with a series of experimental measurements of chain drive efficiency under a range of power, speed and lubrication conditions. Measurements of mechanical efficiency are compared to infrared measurements indicating...