This paper studies the static stability of metal cones subjected to combined, simultaneous action of the external pressure and axial compression. Cones are relatively thick; hence, their buckling performance remains within the elastic-plastic range. The literature review shows that there are very few results within this range and none on combined stability. The current paper aims to fill this gap. Combined stability plot, sometimes called interactive stability plot, is obtained for mild steel models. Most attention is given to buckling caused by a single type of loading, i.e., by hydrostatic external pressure and by axial compression. Asymmetric bifurcation bucklings, collapse load in addition to the first yield pressure and first yield force, are computed using two independent proprietory codes in order to compare predictions given by them. Finally, selected cone configurations are used to verify numerical findings. To this end four cones were computer numerically controlled-machined from a solid steel billet of 252 mm in diameter. All cones had integral top and bottom flanges in order to mimic realistic boundary conditions. Computed predictions of buckling loads, caused by external hydrostatic pressure, were close to the experimental values. But similar comparisons for axially compressed cones are not so good. Possible reasons for this disparity are discussed in the paper.
Skip Nav Destination
Article navigation
November 2010
Materials Technology
Plastic Buckling of Conical Shells
J. Błachut,
J. Błachut
Department of Mechanical Engineering,
University of Liverpool
, Liverpool L69 3GH, UK
Search for other works by this author on:
O. Ifayefunmi
O. Ifayefunmi
Department of Mechanical Engineering,
University of Liverpool
, Liverpool L69 3GH, UK
Search for other works by this author on:
J. Błachut
Department of Mechanical Engineering,
University of Liverpool
, Liverpool L69 3GH, UK
O. Ifayefunmi
Department of Mechanical Engineering,
University of Liverpool
, Liverpool L69 3GH, UKJ. Offshore Mech. Arct. Eng. Nov 2010, 132(4): 041401 (11 pages)
Published Online: September 24, 2010
Article history
Received:
June 18, 2009
Revised:
February 1, 2010
Online:
September 24, 2010
Published:
September 24, 2010
Citation
Błachut, J., and Ifayefunmi, O. (September 24, 2010). "Plastic Buckling of Conical Shells." ASME. J. Offshore Mech. Arct. Eng. November 2010; 132(4): 041401. https://doi.org/10.1115/1.4001437
Download citation file:
Get Email Alerts
Numerical Modeling of Fish Cage Structural Responses in Regular and Irregular Waves Using Modified XPBD
J. Offshore Mech. Arct. Eng (April 2025)
Layout Optimization of Wave Energy Park Based on Multi-Objective Optimization Algorithm
J. Offshore Mech. Arct. Eng (August 2025)
Effects of Aerodynamic Damping and Gyroscopic Moments on Dynamic Responses of a Semi-Submersible Floating Vertical Axis Wind Turbine: An Experimental Study
J. Offshore Mech. Arct. Eng (April 2025)
Investigating the Impact of System Parameters on Flow-Induced Vibration Hard Galloping Based on Deep Neural Network
J. Offshore Mech. Arct. Eng (August 2025)
Related Articles
Buckling of Unstiffened Steel Cones Subjected to Axial Compression and External Pressure
J. Offshore Mech. Arct. Eng (August,2012)
Theory of Elastic Stability: Analysis and Sensitivity
Appl. Mech. Rev (January,2002)
Plastic Buckling of Cones Subjected to Axial Compression and External Pressure
J. Pressure Vessel Technol (February,2013)
Experimental Perspective on the Buckling of Pressure Vessel Components
Appl. Mech. Rev (January,2014)
Related Proceedings Papers
Related Chapters
Openings
Guidebook for the Design of ASME Section VIII Pressure Vessels, Third Edition
Openings
Guidebook for the Design of ASME Section VIII Pressure Vessels
Section VIII: Division 2–Alternative Rules
Companion Guide to the ASME Boiler & Pressure Vessel Codes, Volume 2, Sixth Edition