Elastic, elastic-plastic and experimental stress analyses, and fatigue lifetime predictions are presented for thick cylinders containing multiple, axial holes within the wall. The holes are generally semi-elliptical (including semi-circular), and the cylinders are autofrettaged after introduction of the holes and are subsequently subjected to cyclic pressurization of the bore. Two potentially critical failure locations are identified; a fracture-mechanics based design methodology is proposed; elastic and elastic-plastic finite element (FE) analyses are undertaken. The elastic FE analysis predicts hoop stresses at the bore resulting from internal pressurization which are some 7 percent higher than those for the equivalent plain tube. For a given hole size and location and for nominal overstrains of 40 percent or greater, the residual compressive stress at the bore is reduced by approximately 15 percent below the value for a plain tube of the same radius ratio. Two experimental investigations are reported, one based upon X-ray diffraction, to measure residual stresses and stress gradients, and the other based upon radial tube slitting, to measure opening angle. They confirm most features of the residual stress profiles predicted from FE analysis with the exception of high compressive residual stresses and stress gradients immediately adjacent to the hole boundaries. Appropriate use of the residual stress information permits prediction of tube lifetimes for cracks emanating from the bore and from the hole. For the geometry and loading under consideration, the more critical location is predicted to be the hole boundary, the lifetime for failures originating from this point being some 60 percent of the lifetime for cracks originating at the bore.
Skip Nav Destination
Article navigation
November 1997
Research Papers
Stress Concentration, Stress Intensity, and Fatigue Lifetime Calculations in Autofrettaged Tubes Containing Axial Perforations Within the Wall
A. P. Parker,
A. P. Parker
Royal Military College of Science, Cranfield University, Swindon, SN6 8LA, U.K.
Search for other works by this author on:
S. N. Endersby,
S. N. Endersby
University of Northumbria, Newcastle Upon Tyne, NE1 8ST, U.K.
Search for other works by this author on:
T. J. Bond,
T. J. Bond
University of Northumbria, Newcastle Upon Tyne, NE1 8ST, U.K.
Search for other works by this author on:
J. H. Underwood,
J. H. Underwood
Army Armament R D & E Center, Watervliet, NY 12189
Search for other works by this author on:
S. L. Lee,
S. L. Lee
Army Armament R D & E Center, Watervliet, NY 12189
Search for other works by this author on:
J. Higgins
J. Higgins
Army Armament R D & E Center, Watervliet, NY 12189
Search for other works by this author on:
A. P. Parker
Royal Military College of Science, Cranfield University, Swindon, SN6 8LA, U.K.
S. N. Endersby
University of Northumbria, Newcastle Upon Tyne, NE1 8ST, U.K.
T. J. Bond
University of Northumbria, Newcastle Upon Tyne, NE1 8ST, U.K.
J. H. Underwood
Army Armament R D & E Center, Watervliet, NY 12189
S. L. Lee
Army Armament R D & E Center, Watervliet, NY 12189
J. Higgins
Army Armament R D & E Center, Watervliet, NY 12189
J. Pressure Vessel Technol. Nov 1997, 119(4): 488-493 (6 pages)
Published Online: November 1, 1997
Article history
Received:
August 23, 1996
Revised:
May 7, 1997
Online:
February 11, 2008
Citation
Parker, A. P., Endersby, S. N., Bond, T. J., Underwood, J. H., Lee, S. L., and Higgins, J. (November 1, 1997). "Stress Concentration, Stress Intensity, and Fatigue Lifetime Calculations in Autofrettaged Tubes Containing Axial Perforations Within the Wall." ASME. J. Pressure Vessel Technol. November 1997; 119(4): 488–493. https://doi.org/10.1115/1.2842334
Download citation file:
Get Email Alerts
Cited By
The Behaviour of Elbow Elements at Pure Bending Applications Compared to Beam and Shell Element models
J. Pressure Vessel Technol
Measurement of Steam-Generator-Tube Vibration Damping Caused by Anti-Vibration-Bar Supports
J. Pressure Vessel Technol (February 2025)
Related Articles
Localized Autofrettage as a Design Tool for the Fatigue Improvement of Cross-Bored Cylinders
J. Pressure Vessel Technol (November,1998)
A Comparison of Methods for Predicting Residual Stresses in Strain-Hardening, Autofrettaged Thick Cylinders, Including the Bauschinger Effect
J. Pressure Vessel Technol (May,2006)
Stress Intensity, Stress Concentration, and Fatigue Crack Growth Along Evacuator Holes of Pressurized, Autofrettaged Tubes
J. Pressure Vessel Technol (August,1996)
Bauschinger Effect Design Procedures for Autofrettaged Tubes Including Material Removal and Sachs’ Method
J. Pressure Vessel Technol (November,1999)
Related Chapters
Use of Large Standoff Magnetometry for Geohazard Pipeline Integrity Investigations
Pipeline Integrity Management Under Geohazard Conditions (PIMG)
Subsection NB—Class 1 Components
Companion Guide to the ASME Boiler & Pressure Vessel Code, Volume 1, Second Edition
Subsection NB—Class 1 Components
Companion Guide to the ASME Boiler and Pressure Vessel Code, Volume 1, Fourth Edition