The in situ vapor-phase lubrication of M50 steel, in combined rolling and sliding contacts at 540°C using nitrogen atmospheres containing acetylene, is achieved. Acetylene partial pressures of 0.05 atmospheres are capable of providing continuous lubrication to combined rolling and sliding contacts through pyrolytic carbon deposition. In these tests, friction coefficients as low as μ=0.01 are found for contacts at 2.0 rolling speed, 10 cm/s sliding speed, 100 N load (1.3 GPa Hertzian contact pressure), and ambient temperature of 540°C, with even lower values observed at more modest sliding speeds. One example of a model for vapor phase lubrication of combined rolling and sliding contacts is developed which predicts the lubricant steady-state fractional coverage of the contact surfaces, and from this makes friction coefficient predictions using a linear rule-of-mixture. Friction coefficient responses to step changes in acetylene partial pressure, sliding speed, and disk wear-track diameter are measured. Increased partial pressure of acetylene and increased area available for deposition are observed to be beneficial, while increased sliding speed is detrimental to lubrication performance. Shapes and trends of steady-state friction coefficient versus acetylene partial pressure, sliding speed, and disk wear-track diameter are described and curve-fit by the model. In combined rolling and sliding this example model predicts large regions of operating conditions over which friction coefficient is independent of rolling speed, as well as regions of independence of vapor partial pressure. In the special case of pure sliding, a region of friction coefficient independence of a ratio of partial pressure to sliding speed and another region of independence of a ratio of partial pressure to the product of sliding speed and normal load are predicted.
Skip Nav Destination
Article navigation
July 2001
Technical Papers
Vapor-Phase Lubrication in Combined Rolling and Sliding Contacts: Modeling and Experimentation
W. Gregory Sawyer,
W. Gregory Sawyer
Department of Mechanical Engineering, Aeronautical Engineering and Mechanics, Rensselaer Polytechnic Institute, Troy, NY 12180
Search for other works by this author on:
Thierry A. Blanchet
Thierry A. Blanchet
Department of Mechanical Engineering, Aeronautical Engineering and Mechanics, Rensselaer Polytechnic Institute, Troy, NY 12180
Search for other works by this author on:
W. Gregory Sawyer
Department of Mechanical Engineering, Aeronautical Engineering and Mechanics, Rensselaer Polytechnic Institute, Troy, NY 12180
Thierry A. Blanchet
Department of Mechanical Engineering, Aeronautical Engineering and Mechanics, Rensselaer Polytechnic Institute, Troy, NY 12180
Contributed by the Tribology Division of THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS for presentation at the STLE/ASME Tribology Conference, Seattle, WA, October 1–4. Manuscript received by the Tribology Division Jan. 27, 2000; revised manuscript received July 6, 2000. Paper No. 2000-TRIB-39. Associate Editor: M. M. Khonsari.
J. Tribol. Jul 2001, 123(3): 572-581 (10 pages)
Published Online: July 6, 2000
Article history
Received:
January 27, 2000
Revised:
July 6, 2000
Citation
Sawyer, W. G., and Blanchet, T. A. (July 6, 2000). "Vapor-Phase Lubrication in Combined Rolling and Sliding Contacts: Modeling and Experimentation ." ASME. J. Tribol. July 2001; 123(3): 572–581. https://doi.org/10.1115/1.1308039
Download citation file:
Get Email Alerts
Related Articles
Characterization of Pelletized MoS 2 Powder Particle Detachment Process
J. Tribol (July,2001)
Synthesis and Lubrication Characteristics of Aryloxycyclophosphazenes Substituted With Imidazolium
J. Tribol (July,2009)
Comparisons of Tribological and Vibration Behaviors of Textured Point Contacts of Bearing Steel Lubricated With Oil and Grease Under Starved Conditions
J. Tribol (July,2016)
Introduction to Tribology
Appl. Mech. Rev (January,2003)
Related Chapters
Contact Laws
Contact in Structural Mechanics: A Weighted Residual Approach
How the Worm Gear Developed through Time
Design and Application of the Worm Gear
On the Evaluation of Thermal and Mechanical Factors in Low-Speed Sliding
Tribology of Mechanical Systems: A Guide to Present and Future Technologies