Frictional heating occurring during pin-on-flat tribotesting of ultrahigh molecular weight polyethylene (UHMWPE) pins was measured and modeled. A full factorial experiment was conducted to determine if testing parameters can produce sufficient frictional heat to alter tribological properties of the bovine serum used as lubricant in the system. Temperature of the surrounding bovine serum was monitored during tribotests using varying pin sizes and sliding speeds to determine typical temperature rises due to frictional heating. This work examined two sliding speeds (40 mm/s and 80 mm/s) and two pin diameters (6.35 mm and 9.5 mm) at a single static load. Gravimetric analysis for wear determination and coefficient of friction measurement were performed for each test. Results showed that frictional heating increased the bulk temperature of the surrounding serum and correlated to sliding speed and average coefficient of friction. No correlation was seen at this temperature range between serum temperature rise and wear rate, providing evidence that the tested parameters are acceptable for tribotesting of UHMWPE. A computational model was developed to predict bulk serum temperature increase. This model closely predicted the temperature increase to within 2 °C, which is sufficient accuracy for identifying if bovine serum protein precipitation is likely during tribotesting. This work serves as an initial estimate and prediction for appropriate testing parameters based on lubricant responses to frictional heating.
Skip Nav Destination
Article navigation
October 2016
Research-Article
Experimental and Computational Thermal Modeling of In Vitro Pin-on-Disk Tests of Ultra High Molecular Weight Polyethylene
Kathleen A. Lewicki,
Kathleen A. Lewicki
Thayer School of Engineering
at Dartmouth College,
14 Engineering Drive,
Hanover, NH 03755
e-mail: kathleen.a.lewicki.th@dartmouth.edu
at Dartmouth College,
14 Engineering Drive,
Hanover, NH 03755
e-mail: kathleen.a.lewicki.th@dartmouth.edu
Search for other works by this author on:
Douglas W. Van Citters
Douglas W. Van Citters
Mem. ASME
Thayer School of Engineering
at Dartmouth College,
14 Engineering Drive,
Hanover, NH 03755,
e-mail: dvancitters@dartmouth.edu
Thayer School of Engineering
at Dartmouth College,
14 Engineering Drive,
Hanover, NH 03755,
e-mail: dvancitters@dartmouth.edu
Search for other works by this author on:
Kathleen A. Lewicki
Thayer School of Engineering
at Dartmouth College,
14 Engineering Drive,
Hanover, NH 03755
e-mail: kathleen.a.lewicki.th@dartmouth.edu
at Dartmouth College,
14 Engineering Drive,
Hanover, NH 03755
e-mail: kathleen.a.lewicki.th@dartmouth.edu
Douglas W. Van Citters
Mem. ASME
Thayer School of Engineering
at Dartmouth College,
14 Engineering Drive,
Hanover, NH 03755,
e-mail: dvancitters@dartmouth.edu
Thayer School of Engineering
at Dartmouth College,
14 Engineering Drive,
Hanover, NH 03755,
e-mail: dvancitters@dartmouth.edu
Contributed by the Tribology Division of ASME for publication in the JOURNAL OF TRIBOLOGY. Manuscript received June 22, 2015; final manuscript received November 9, 2015; published online July 8, 2016. Assoc. Editor: Zhong Min Jin.
J. Tribol. Oct 2016, 138(4): 041602 (7 pages)
Published Online: July 8, 2016
Article history
Received:
June 22, 2015
Revised:
November 9, 2015
Citation
Lewicki, K. A., and Van Citters, D. W. (July 8, 2016). "Experimental and Computational Thermal Modeling of In Vitro Pin-on-Disk Tests of Ultra High Molecular Weight Polyethylene." ASME. J. Tribol. October 2016; 138(4): 041602. https://doi.org/10.1115/1.4032819
Download citation file:
Get Email Alerts
Cited By
Static Characteristics of Hybrid Water-Lubricated Herringbone Groove Journal Bearing
J. Tribol (April 2025)
Related Articles
Tribological Behavior of Diamondlike Carbon Film-Deposited Ti6Al4V Alloy Swinging Against Ultrahigh Molecular Weight Polyethylene in Fetal Bovine Serum
J. Tribol (May,2017)
Tribological Properties and Microstructure Evolution of Ultra-High Molecular Weight Polyethylene
J. Tribol (April,1999)
Enhanced Tribological Performance of UHMWPE Composites Reinforced with Wollastonite: biocompatibility and Wear Behavior
J. Tribol (January,0001)
Effect of Contact Area on the Wear and Friction of UHMWPE in Circular Translation Pin-on-Disk Tests
J. Tribol (November,2017)
Related Proceedings Papers
Related Chapters
Materials
Design and Application of the Worm Gear
Contact Laws
Contact in Structural Mechanics: A Weighted Residual Approach
Cultural Impediments to Practical Modeling of Wear Rates
Tribological Modeling for Mechanical Designers