The present study is focused on the performance evaluation of MoS2, H3BO3, and multiwall carbon nanotubes (MWCNT) used as the potential oil additives in base oil for aluminum metal matrix composites (AMMC)–steel (EN31) tribocontact. Al–B4C composite is used for this purpose; based on a set of preliminary investigation under unlubricated and fresh oil lubrication, three different types of AMMCs (Al–SiC, Al–B4C, and Al–SiC–B4C) were used. A pin-on-disk tribometer is used for all the friction and wear tests under operating condition of load 9.8 N and sliding velocity of 0.5 m/s. From the particle-based wet tribology, it is clear that both the additives H3BO3 and MWCNT improve the friction as well as wear behavior for selected composite contacts. Multiwall carbon nanotubes emerged out as superior among all the additives, whereas MoS2 additives show marginal enhancement in frictional performance under given operating conditions. Fractography and morphological study of pin specimens are carried out to identify the underlying friction and wear mechanisms.
Skip Nav Destination
Article navigation
July 2018
Research-Article
Influence of MoS2, H3BO3, and MWCNT Additives on the Dry and Lubricated Sliding Tribology of AMMC–Steel Contacts
Harpreet Singh,
Harpreet Singh
Mechanical Engineering Department,
Thapar University,
Patiala 147004, Punjab, India
e-mail: harpreetsingh6n2016@gmail.com
Thapar University,
Patiala 147004, Punjab, India
e-mail: harpreetsingh6n2016@gmail.com
Search for other works by this author on:
ParamPreet Singh,
ParamPreet Singh
Mechanical Engineering Department,
Thapar University,
Patiala 147004, Punjab, India
e-mail: psingh.param@gmail.com
Thapar University,
Patiala 147004, Punjab, India
e-mail: psingh.param@gmail.com
Search for other works by this author on:
Hiralal Bhowmick
Hiralal Bhowmick
Mechanical Engineering Department,
Thapar University,
Patiala 147004, Punjab, India
e-mail: hiralal.bhowmick@thapar.edu
Thapar University,
Patiala 147004, Punjab, India
e-mail: hiralal.bhowmick@thapar.edu
Search for other works by this author on:
Harpreet Singh
Mechanical Engineering Department,
Thapar University,
Patiala 147004, Punjab, India
e-mail: harpreetsingh6n2016@gmail.com
Thapar University,
Patiala 147004, Punjab, India
e-mail: harpreetsingh6n2016@gmail.com
ParamPreet Singh
Mechanical Engineering Department,
Thapar University,
Patiala 147004, Punjab, India
e-mail: psingh.param@gmail.com
Thapar University,
Patiala 147004, Punjab, India
e-mail: psingh.param@gmail.com
Hiralal Bhowmick
Mechanical Engineering Department,
Thapar University,
Patiala 147004, Punjab, India
e-mail: hiralal.bhowmick@thapar.edu
Thapar University,
Patiala 147004, Punjab, India
e-mail: hiralal.bhowmick@thapar.edu
1Corresponding author.
Contributed by the Tribology Division of ASME for publication in the JOURNAL OF TRIBOLOGY. Manuscript received August 14, 2017; final manuscript received November 10, 2017; published online February 9, 2018. Assoc. Editor: Sinan Muftu.
J. Tribol. Jul 2018, 140(4): 041801 (10 pages)
Published Online: February 9, 2018
Article history
Received:
August 14, 2017
Revised:
November 10, 2017
Citation
Singh, H., Singh, P., and Bhowmick, H. (February 9, 2018). "Influence of MoS2, H3BO3, and MWCNT Additives on the Dry and Lubricated Sliding Tribology of AMMC–Steel Contacts." ASME. J. Tribol. July 2018; 140(4): 041801. https://doi.org/10.1115/1.4038957
Download citation file:
Get Email Alerts
Related Articles
Synergistic Lubricating Performance of h-BN/GF Nanoparticles as Oil Additives for Steel-Steel Contact
J. Tribol (June,2022)
Influence of Carbon Nanotubes on Conductive Capacity and Tribological Characteristics of Poly(ethylene Glycol-Ran-Propylene Glycol) Monobutyl Ether as Base Oil of Grease
J. Tribol (January,2016)
Related Proceedings Papers
Related Chapters
Contact Laws
Contact in Structural Mechanics: A Weighted Residual Approach
The Tribological Character of LB Films of Dipalmitoylphosphatidylcholine (DPPC)
International Conference on Mechanical and Electrical Technology, 3rd, (ICMET-China 2011), Volumes 1–3
Wear and Contact Fatigue Properties of a Novel Lubricant Additive
Bearing and Transmission Steels Technology