1-11 of 11
Keywords: mechanical properties
Close
Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Journal Articles
Article Type: Research Papers
J. Tribol. July 2022, 144(7): 071703.
Paper No: TRIB-21-1122
Published Online: February 8, 2022
...Aluru Praveen Sekhar; Debdulal Das This study aims to correlate the abrasive wear performance with mechanical properties, considering AA6063 Al–Mg–Si alloy as the model material. The selected alloy specimens are subjected to artificial ageing at 150 °C for an ageing duration ranging from 1 to 672 h...
Journal Articles
Article Type: Research Papers
J. Tribol. June 2022, 144(6): 061703.
Paper No: TRIB-21-1345
Published Online: December 8, 2021
...Partha Haldar; Tapas Kumar Bhattacharya; Nipu Modak The study emphasized the sintering behavior and tribo-mechanical properties of alumina ceramics by nano-TiO 2 addition as a sintering aid. With increase in sintering temperature, the bulk density of alumina has increased gradually and optimized...
Journal Articles
Article Type: Research Papers
J. Tribol. February 2022, 144(2): 021702.
Paper No: TRIB-20-1528
Published Online: May 4, 2021
... Email: cuizhenxiang@baosteel.com Email: niuchao@baosteel.com Contributed by the Tribology Division of ASME for publication in the J ournal of T ribology . 14 12 2020 03 04 2021 03 04 2021 04 05 2021 sliding wear mechanical properties contact sliding deep...
Journal Articles
Article Type: Research Papers
J. Tribol. September 2021, 143(9): 091901.
Paper No: TRIB-20-1106
Published Online: January 13, 2021
... ratios of Ti 0.7 -DLC and Ti 23.3 -DLC were the highest and lowest, respectively. Table 3 Mechanical properties of the DLC coatings Coating Hardness (GPa) Elasticity modulus (GPa) H/E H 3 /E 2 (GPa) Pure DLC 19.5 ± 1.24 156.3 ± 10.05 0.12 0.30 Ti 0.7 -DLC 22.9...
Journal Articles
Article Type: Research Papers
J. Tribol. April 2021, 143(4): 041401.
Paper No: TRIB-20-1272
Published Online: September 28, 2020
... of PTFE/PEEK composite with different PTFE volume fractions on a steel counterface. Quantitative relationships between PTFE/PEEK composite friction coefficient and constituent material mechanical properties are then established to facilitate the subsequent investigation of friction mechanisms...
Journal Articles
Article Type: Research Papers
J. Tribol. January 2011, 133(1): 012201.
Published Online: December 2, 2010
... packing rings stuffing box mechanical properties leak tests FE modeling The sealing of valve stems is ensured by the traditional system of packed stuffing boxes. The performance of the stuffing box depends on the level of the radial contact pressure generated by the axial packing compression...
Journal Articles
Article Type: Technical Papers
J. Tribol. July 2001, 123(3): 641–650.
Published Online: October 31, 2000
... which carbon material is removed at extremely low rates, yielding insignificantly small changes in the wear pattern depth, of the order of a few Angstroms per wear cycle. Although the films deposited under 0 and −300 V substrate bias voltage exhibit similar mechanical properties (films #15 and #19...
Journal Articles
Article Type: Technical Papers
J. Tribol. October 2001, 123(4): 670–675.
Published Online: August 31, 2000
...B. Podgornik; M. Kalin; J. Vizˇintin; F. Vodopivec, Professor In fretting wear, the microstructure and the mechanical properties of the surface and subsurface layer depend significantly on the temperature field produced in the fretting zone. Information reported in the literature indicate...
Journal Articles
Article Type: Technical Papers
J. Tribol. October 2001, 123(4): 717–724.
Published Online: July 25, 2000
... affecting the composition and residual stress in the films influence the nanowear resistance of the films. 09 February 2000 25 July 2000 nanostructured materials thin films carbon chromium titanium compounds carbon compounds mechanical properties hardness wear resistance tribology...
Journal Articles
Article Type: Technical Papers
J. Tribol. July 2001, 123(3): 624–631.
Published Online: July 25, 2000
... factors when considering the performance of a new biomaterial in vivo or when engineering tissue replacements that are bioactive. However, component life can also be limited by inadequate surface mechanical properties. Poor surface mechanical properties may lead to failure due to various wear, fracture...
Journal Articles
Article Type: Technical Papers
J. Tribol. July 2000, 122(3): 646–649.
Published Online: October 28, 1999
... coatings were also investigated. The test results showed that HVAS coatings had better mechanical properties than those of regular arc sprayed coatings. The bonding strength of HVAS Al and 3Cr13 coatings was increased by 114 percent and 51.8 percent; the relative wear resistance of HVAS coatings was about...
Topics: Coatings, Sprays