Accurate estimation of slip factor is of paramount importance to ensure centrifugal compressor work input is adequately predicted during the preliminary design process. However, variations in the flow field at impeller exit in both the pitchwise and spanwise directions complicate the evaluation procedure considerably. With the increasing implementation of engine downsizing technologies in the automotive sector, achieving a wide operating range has become a factor of prime importance for centrifugal compressors used in automotive turbocharging applications. As a result of the design features required to achieve this aim, modern impeller geometries have been shown to exhibit an approximately parabolic variation in slip factor across their respective operating maps. By comparison, traditional slip correlations typically exhibit a constant, or at best monotonic, relationship between slip factor and impeller exit flow coefficient. It is this lack of modeling fidelity which the current work seeks to address. In order to tackle these shortcomings, it is proposed that the impeller exit flow should be considered as being made up of three distinct regions: a region of recirculation next to the shroud providing aerodynamic blockage to the stage active flow, and a pitchwise subdivision of the active flow region into jet and wake components. It is illustrated that this hybrid approach in considering both spanwise and pitchwise stratification of the flow permits a better representation of slip factor to be achieved across the operating map. The factors influencing the relative extent of each of these three distinct regions of flow are numerous, requiring detailed investigations to successfully understand their sources and to characterize their extent. A combination of 3D computational fluid dynamics (CFD) data and gas stand test data for six automotive turbocharger compressor stages was employed to achieve this aim. Through application of the extensive interstage static pressure data gathered during gas stand testing at Queen's University Belfast, the results from the 3D CFD models were validated, thus permitting a more in-depth evaluation of the flow field in terms of locations and parameters that could not easily be measured under gas stand test conditions. Building on previous knowledge gained about the variation in shroud side recirculation with geometry and operating condition, the characteristic jet/wake flow structure emanating from the active flow region of the impeller was represented in terms of area and mass flow components. This knowledge allowed individual slip factor values for the jet and wake to be calculated and combined to give an accurate passage average value which exhibited the distinctive nonlinear variation in slip across the operating map which is frequently absent from existing modeling methods. Fundamental considerations of the flow phenomena in each region provided explanation of the results and permitted a modeling approach to be derived to replicate the trends observed in both the experimental data and the CFD simulations.

References

1.
Harley
,
P.
,
Spence
,
S. W.
,
Filsinger
,
D.
,
Dietrich
,
M.
, and
Early
,
J.
,
2014
, “
Meanline Modeling of Inlet Recirculation in Automotive Turbocharger Centrifugal Compressors
,”
ASME J. Turbomach.
,
137
(
1
), p.
011007
.
2.
Stuart
,
C.
,
Spence
,
S. W.
,
Filsinger
,
D.
,
Starke
,
A.
, and
Kim
,
S. I.
,
2018
, “
Characterizing the Influence of Impeller Exit Recirculation on Centrifugal Compressor Work Input
,”
ASME J. Turbomach.
,
140
(
1
), p. 011005.
3.
Japikse
,
D.
,
1985
, “
Assessment of Single and Two-Zone Modelling of Centrifugal Compressors, Studies in Component Performance—Part 3
,”
ASME
Paper No. 85-GT-73.
4.
Eckardt
,
D.
,
1978
, “
Investigation of the Jet-Wake Flow of a Highly Loaded Centrifugal Compressor Impeller
,” National Aeronautics and Space Administration, Washington, DC, Report No.
NASA-TM-75232
.https://ntrs.nasa.gov/search.jsp?R=19780008108
5.
Whitfield
,
A.
,
1974
, “
Slip Factor of a Centrifugal Compressor and Its Variation With Flow Rate
,”
Proc. Inst. Mech. Eng.
,
188
(
1
), pp.
415
423
. pp
6.
Dean
,
R. C.
,
Wright
,
D.
, and
Runstadler
,
P. W.
,
1970
, “
Fluid Mechanics Analysis of High-Pressure-Ratio Centrifugal Compressor Data
,” U.S. Army Aviation Materiel Laboratories, Fort Eustis, VA, Report No.
69-76
.http://www.academia.edu/4040320/USAAVLABS_TECHNICAL_REPORT_65-79_AN_INVESTIGATION_OF_END_PLATES_TO_REDUCE_THE_DRAG_OF_PLANAR_WINGSAN_INVESTIGATION_OF_END_PLATES_TO_REDUCE_THE_DRAG_OF_PLANAR_WINGSCONTENTS
7.
Qiu
,
X.
,
Japikse
,
D.
,
Zhao
,
J.
, and
Anderson
,
M. R.
,
2011
, “
Analysis and Validation of a Unified Slip Factor Model for Impellers at Design and Off-Design Conditions
,”
ASME J. Turbomach.
,
133
(
4
), p.
041018
.
8.
Weisner
,
F. J.
,
1967
, “
A Review of Slip Factors for Centrifugal Impellers
,”
ASME J. Eng. Power
,
89
, pp.
558
572
.
9.
Stodola
,
A.
,
1945
,
Steam and Gas Turbines
,
McGraw-Hill
,
New-York
.
10.
Moore
,
J.
,
Moore
,
J. G.
, and
Johnson
,
M. W.
,
1977
, “
On Three-Dimensional Flow in Centrifugal Impellers
,” Aeronautical Research Council, London, Paper No. 1384.
11.
Stern
,
F.
,
Wilson
,
R. V.
,
Coleman
,
E. W.
, and
Paterson
,
E. G.
,
2001
, “
Comprehensive Approach to Verification and Validation of CFD Simulations—Part 1: Methodology and Procedures
,”
ASME J. Fluids Eng.
,
123
(
4
), pp.
793
802
.
12.
Lüdtke
,
K. H.
,
2004
,
Process Centrifugal Compressors: Basics, Function, Operation, Design, Application
,
Springer-Verlag
,
Berlin
.
13.
Weber
,
C. R.
, and
Koronowski
,
M. E.
,
1986
, “
Meanline Performance Prediction of Volutes in Centrifugal Compressors
,”
ASME
Paper No. 86-GT-216.
14.
Hong
,
S. S.
, and
Kang
,
S. H.
,
2002
, “
Exit Flow Measurements of a Centrifugal Pump Impeller
,”
KSME Int. J.
,
16
(
9
), pp.
1147
1155
.
15.
Sirakov
,
B.
, and
Casey
,
M.
,
2011
, “
Evaluation of Heat Transfer Effects on Turbocharger Performance
,”
ASME
Paper No. GT2011-45887.
16.
Hildebrandt
,
A.
, and
Genrup
,
M.
,
2007
, “
Numerical Investigation of the Effect of Different Back Sweep Angle and Exducer Width on the Impeller Outlet Flow Pattern of a Centrifugal Compressor With Vaneless Diffuser
,”
ASME J. Turbomach.
,
129
(
4
), pp.
429
433
.
You do not currently have access to this content.